1
General Discussion / Re: Best Network Setup
« on: November 29, 2015, 07:00:07 pm »
Changed my mind..I think that I will setup with SERVER serving DHCP and use DHCP reservations. Using this setup..
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
General Discussion / Best Network Setup
« on: November 29, 2015, 02:54:17 am »
I have 2 choices of network setup... Which do you all prefer and why?
MODEM<-static->OPNsense<-DHCP->HUB<-->SERVER&WORKSTATIONS (OPNsense serves DHCP)
MODEM<-statc->OPNsense<-static->SERVER<-DHCP->HUB&WORKSTATIONS (Server serves DHCP)
In the second option the server has a WAN Port for the OPNsense appliance and a LAN port to serve the workstations
FOr the second option I need to know how to setup a static IP between the server and OPNsense appliance
MODEM<-static->OPNsense<-DHCP->HUB<-->SERVER&WORKSTATIONS (OPNsense serves DHCP)
MODEM<-statc->OPNsense<-static->SERVER<-DHCP->HUB&WORKSTATIONS (Server serves DHCP)
In the second option the server has a WAN Port for the OPNsense appliance and a LAN port to serve the workstations
FOr the second option I need to know how to setup a static IP between the server and OPNsense appliance
3
General Discussion / Re: Looking for recommended Configuration.
« on: November 25, 2015, 04:31:36 am »
I would like to try a port forward.. However, the config of the NAT forwarding is a little more than I am used to....
I know the wan IP (27.134.6.91) and the IP of the computer I am wanting to remote to (192.168.3.101).. I also know that I want to forward port 3389... but where to put all the numbers i dunno...
I know the wan IP (27.134.6.91) and the IP of the computer I am wanting to remote to (192.168.3.101).. I also know that I want to forward port 3389... but where to put all the numbers i dunno...
4
General Discussion / Re: How do I remote in?
« on: November 24, 2015, 03:15:21 pm »
How do I configure a port forward on OPNsense. I am used to doing port forwarding on basic routers, but cannot find the same terminology or similar looking interface to enter the port forward to my server...
5
General Discussion / Re: Looking for recommended Configuration.
« on: November 23, 2015, 03:02:37 am »
I only have one server and have put the appliance between the modem and server... I am able to access the internet so I think I have all the basics (default) right...
6
General Discussion / How do I remote in?
« on: November 23, 2015, 02:56:01 am »
I really appreciate all the help you all have given me in implementing OPNsense in my office.
I have installed OPNsense on an appliance and have it installed between my modem and my server...
I have windows 7 pro at home and windows 2008 R2 at my office.
What must I do to be able to remote into my server at my office?
I have installed OPNsense on an appliance and have it installed between my modem and my server...
I have windows 7 pro at home and windows 2008 R2 at my office.
What must I do to be able to remote into my server at my office?
7
General Discussion / Looking for recommended Configuration.
« on: November 17, 2015, 04:04:38 am »
I am somewhat a newb to firewall software.
I want to be able to remote in. Not sure how to set that up with OPNsense.
Also, I am setting this up for a dentist office that has a local server. The main software runs local on the server. The office only uses the internet for surfing, backup and updates.
What is the recommended configuration for OPNsense?
What things should I be careful not to screw up configuration wise?
I want to be able to remote in. Not sure how to set that up with OPNsense.
Also, I am setting this up for a dentist office that has a local server. The main software runs local on the server. The office only uses the internet for surfing, backup and updates.
What is the recommended configuration for OPNsense?
What things should I be careful not to screw up configuration wise?
8
General Discussion / Re: What wifi dongle is most friendly to OPNsense
« on: November 17, 2015, 04:00:13 am »
Went ahead with a TP-LINK TL-WR841HP 300Mbps High Power Wireless N Router... Working really nice 
9
General Discussion / Re: [SOLVED] Cheap Box that meets requirements
« on: November 17, 2015, 03:58:55 am »What do you all think of this option for future referece?
http://www.amazon.com/gp/product/B00TD8MTFY?refRID=JKASFWPB77V21VCEE237&ref_=pd_lutyp_simh_2_4
Really Nice!! Runs fast and silent!
10
General Discussion / Re: Fatal Error
« on: November 17, 2015, 03:58:01 am »
Used AMD64 VGA IMG and USB install worked like a charm. Runs flawlessly..
11
General Discussion / Re: USB Install - failed to
« on: November 17, 2015, 03:57:02 am »
BINGO, used rufus with vga amd64 img and worked like a charm!!
12
General Discussion / [SOLVED] USB Install - failed to open PhysicalDrive1
« on: November 16, 2015, 04:38:40 pm »
Downloaded the Nano AMD64 img file and tried to use physdiskwrite -u to write it to my usb
Failed to open \\. \PhysicalDrive1 - exiting
Failed to open \\. \PhysicalDrive1 - exiting
13
General Discussion / Re: Recommended Enterprise AV solution
« on: November 13, 2015, 01:06:10 am »
Trend Micro gave a great deal on a subscription with central management endpoint AV. 11 workstations for $550 for 3 years.
14
General Discussion / Re: What wifi dongle is most friendly to OPNsense
« on: November 13, 2015, 01:04:36 am »
OK, thanks for the info
15
General Discussion / Re: Fatal Error
« on: November 13, 2015, 01:03:55 am »
I will be back in the office on Monday.. It is the most recent download...
Pages: [1] 2