Messages

1

19.7 Production Series / Re: High CPU Usage since upgrade from 19.1.10 to 19.7

« on: July 18, 2019, 03:58:48 am »

yes I'm seeing higher CPI than normal

usually no more than 20% peek but now upto 35% (i7 chip)

2

19.7 Production Series / Re: Upgrade to 19.7 lost ipv6

« on: July 18, 2019, 03:46:29 am »

WORKAROUND - TEMP FIX


If I go to LAN and tick Allow manual adjustment of DHCPv6 and Router Advertisements under the track interfaces section

Then configure the dhcp6 server via

Services: DHCPv6: [LAN]

I tick enable Server and set the range to the full available range

and Router Advertisements via

Services: Router Advertisements: [LAN]

I select Assisted

I believe these are the automatic defaults anyway when using Track interface without manual adjustment 

I can create a functioning IPv6 system again so suspect the error is simply a config setting not being honoured in automatic mode for Track Interface

3

19.7 Production Series / Re: Upgrade to 19.7 lost ipv6

« on: July 17, 2019, 05:49:43 pm »

@franco

FYI this is my french system which uses track WAN for IPv6

My UK system is still on 19.7.RC1 using a fixed IPV6 and is working fine

4

19.7 Production Series / Re: Upgrade to 19.7 lost ipv6

« on: July 17, 2019, 04:54:12 pm »

root@home:~ # grep -i ipaddrv6 /conf/config.xml
      <ipaddrv6>dhcp6</ipaddrv6>
      <ipaddrv6>track6</ipaddrv6>

5

19.7 Production Series / Upgrade to 19.7 lost ipv6

« on: July 17, 2019, 04:00:13 pm »

After upgrading to 19.7 I still get an IPv6 address on LAN and can ping this IPv6 address from remote locations

However no devices on LAN are being given IPv6 address

I noticed dhcp6d server was not running and is stopped after each reboot until manually started

But even after manually starting dhcp6d server not clients are being given IPv6 address

Cant see anything obvious on logs

EDIT: it appears there is no /etc/dhcp6v.conf file being created anymore suspect thats not helping

EDIT2: clients that had IPv6 before the update have kept them and function correctly although I suspect they will lose that connectivity when the lease expires 


EDIT3: See my workaround in my last post

6

19.7 Production Series / Re: upgraded from 19.1.10 to 19.7r1, NetFlow data is not working

« on: July 12, 2019, 09:49:55 am »

Thanks that seems to fix it

7

19.7 Production Series / Re: upgraded from 19.1.10 to 19.7r1, NetFlow data is not working

« on: July 11, 2019, 06:18:02 pm »

Seeing the same here. Can see activity but no data

No amount of resets or repair seems to work

8

19.7 Production Series / Re: VLAN interfaces

« on: July 11, 2019, 09:54:59 am »

That fixed the VLAN issue thanks Franco

Interestingly flowd_aggregate   Insight Aggregator will no longer start at boot. Is this connected ?

trying to start from the GUI I see the following in log but still doesn't start

Jul 11 08:54:34   /flowd_aggregate.py: startup, check database.

I reset the netflow data and all is good again

9

19.7 Production Series / Re: VLAN interfaces

« on: July 10, 2019, 06:04:06 pm »

Yep that did it sending the two config files now to you email add

10

19.7 Production Series / Re: VLAN interfaces

« on: July 10, 2019, 05:57:08 pm »

ok rebooting now

11

19.7 Production Series / Re: VLAN interfaces

« on: July 10, 2019, 05:54:19 pm »

I have to admit I didn't save the config right after boot I have the current one obviously which is after the apply

I do have config from a few weeks ago which will not have changed if that helps

12

19.7 Production Series / [SOLVED] VLAN interfaces

« on: July 10, 2019, 02:35:09 pm »

After upgrade to 19.7.rc1 all my VLANs with the exception of the default LAN where inoperable, no access to them and devices on then not able to reach the internet. No obvious error messages i could see.

Quick save of the effected VLAN interfaces from the console resolved the issue. Any logs I can provide that might help ?

13

French - Français / Re: Orange remplacer livebox - Aucune modification nécessaire

« on: May 08, 2019, 01:08:55 pm »

devrait être le même

14

19.1 Legacy Series / Re: WOL plugin error after upgrade to 19.1.5_1

« on: April 06, 2019, 06:55:14 am »

Dam and I searched as well. must get some glasses

Thanks for pointing it out

15

19.1 Legacy Series / [SOLVED] WOL plugin error after upgrade to 19.1.5_1

« on: April 05, 2019, 09:49:57 pm »

Getting this error

 [05-Apr-2019 20:47:25 Europe/London] PHP Warning:  count(): Parameter must be an array or an object that implements Countable in /usr/local/www/widgets/widgets/wake_on_lan.widget.php on line 64

Tried a reinstall of the plugin but same issue