Messages

I have setup 2 Adguard Home DNS server in Raspberry Pi and was wondering what should go into the Use Gateway field? The drop down shows Wan DHCP6 IPV6 address and Wan DHCP IPV4 address.
And secondly, how to setup primary and secondary DNS so the secondary becomes active when the primary is down? As is, if I turn off the primary, 192.168.4.209 DNS, the LAN devices does not use the secondary DNS 192.168.4.208. Under Services DHCPv4 i have bother DNS listed.

I did not do any tuning.
This is with normal daily usage for the household of 3 adults.

Is there a benchmark of some sort for this zones?
Are this numbers within acceptable range with browsing in 2 laptops, couple of streaming devices and 3 phones?

The Core 0,1,2,3 (dev.cpu.0.temperature) 52.0 degree C
Zone 0 (hw.acpi.thermal.tz0.temperature) is at 27.9 c constant.

The Core 0,1,2,3 (dev.cpu.0.temperature) is always hovering at 52.0 degree C but some time spikes to 58 C for a second or so.
The Zone 0 (hw.acpi.thermal.tz0.temperature) is at 27.9 c constant.

I juts installed os-hw-probe.

Update:
I ended up buying a bare bone from Alibaba for $117.00. I installed 16 gig ram and a 500 gb M.2 2280 NVMe ssd.
I installed Opnsense 23.7.3 and been up for 24+ hrs. So far no issue.

https://www.aliexpress.us/item/3256805037671566.html?spm=a2g0o.order_detail.order_detail_item.3.629df19cS64dCK&gatewayAdapt=glo2usa

I just configured IPV6 in my router, It's working with AT&T Comcast.
I need some help setting up some basic firewall rules to protect my LAN devices.
Can you point me to some kind of documentation or write up more of newbi friendly?

I'm running 23.7.3 in a X86 device.

I need some recommendation for my next HW.
I am using an x86 fan less PC with 2 ports but need to get a new hardware. The X86 is about to die any day.
I'm looking into Zimaboard 432.
I have an At&t gig fiber, the At&t modem is set for Passthru mode.
I have 2 Unifi AP AC Lite an Unifi 8-60 POE switch.
I am not using any VLANs but would like to take advantage of the At&t IPV6 as well.

We are 4 users in the house, 8 to 10 cameras, few streaming devices and 2 of us work from home.
My budged is $200.00 US range.

Any advice or suggestions?

I wanted to move this to Zenarmor thread but did not know how, so I created a dup of this in that thread.

I am running 21.1.6.
I have experienced twice in last month an a half that my router stopped receiving IPV4 WAN address from the AT&T pass thru modem. It does not lose the IPV6 address.
I had to reboot to get it back up and running.

What could cause this?
For troubleshooting this, what logs should I be looking into? I have Zenarmor- Sensei setup for LAN interface, and this is what I saw in the System Diagnostic Activity. Can this be the reason, "HeapDumpOnOutOfMemoryError"?
My box has 8 GIG of memory and Intel core i5 2.30 GHZ 4 core cpu.

• /usr/local/openjdk8/bin/java -Xms2g -Xmx2g -XX:+UseConcMarkSweepGC -XX:CMSInitiatingOccupancyFraction=75 -XX:+UseCMSInitiatingOccupancyOnly -XX:+AlwaysPreTouch -server -Xss1m -Djava.awt.headless=true -Dfile.encoding=UTF-8 -Djna.nosys=true -Djdk.io.permissionsUseCanonicalPath=true -Dio.netty.noUnsafe=true -Dio.netty.noKeySetOptimization=true -Dio.netty.recycler.maxCapacityPerThread=0 -Dlog4j.shutdownHookEnabled=false -Dlog4j2.disable.jmx=true -Dlog4j.skipJansi=true -XX:+HeapDumpOnOutOfMemoryError -Des.path.home=/usr/local/lib/elasticsearch -cp /usr/local/lib/elasticsearch/lib/* org.elasticsearch.bootstrap.Elasticsearch -d --pidfile=/var/run/elasticsearch/elasticsearch.pid -Epath.conf=/usr/local/etc/elasticsearch{VM Periodic Task Th}

I am running 21.1.6.
I have experienced twice in last month an a half that my router stopped receiving IPV4 WAN address from the AT&T pass thru modem. It does not lose the IPV6 address.
I had to reboot to get it back up and running.

What could cause this?
For troubleshooting this, what logs should I be looking into? I have Zenarmor- Sensei setup for LAN interface, and this is what I saw in the System Diagnostic Activity. Can this be the reason, "HeapDumpOnOutOfMemoryError"?
My box has 8 GIG of memory and Intel core i5 2.30 GHZ 4 core cpu.

• /usr/local/openjdk8/bin/java -Xms2g -Xmx2g -XX:+UseConcMarkSweepGC -XX:CMSInitiatingOccupancyFraction=75 -XX:+UseCMSInitiatingOccupancyOnly -XX:+AlwaysPreTouch -server -Xss1m -Djava.awt.headless=true -Dfile.encoding=UTF-8 -Djna.nosys=true -Djdk.io.permissionsUseCanonicalPath=true -Dio.netty.noUnsafe=true -Dio.netty.noKeySetOptimization=true -Dio.netty.recycler.maxCapacityPerThread=0 -Dlog4j.shutdownHookEnabled=false -Dlog4j2.disable.jmx=true -Dlog4j.skipJansi=true -XX:+HeapDumpOnOutOfMemoryError -Des.path.home=/usr/local/lib/elasticsearch -cp /usr/local/lib/elasticsearch/lib/* org.elasticsearch.bootstrap.Elasticsearch -d --pidfile=/var/run/elasticsearch/elasticsearch.pid -Epath.conf=/usr/local/etc/elasticsearch{VM Periodic Task Th}

I also have found since updating to 22.1 that RA would not start.
After much messing and many reboots, I removed the DNS servers entries I had in all the interfaces on RA and rebooted and it started working.
I then put them back again (to the DNS servers I wanted in there) and rebooted again.

Now it SEEMS to be back to normal.... in that RA starts on boot up and the problem has gone.... I think....

Chris

I am having the same issue. RA, what is this and where is it in GUI?

I have a simple setup of Opnsense+PiHole.
I have assigned the IP of my PiHole to the DNS field in DHCP of Opnsense.
Should I use PiHole's IP in the System- Setting - General in the DNS field or use something like 9.9.9.9 in the system DNS box?

Hi,

What if you install ubench manually?

pkg install -fy ubench

When I try to install ubench manually it gave the beloww out put, but I think after running pkg clean something good happened. The configuration went on and completed.
pkg install -y ubench
Updating OPNsense repository catalogue...
OPNsense repository is up to date.
Updating SunnyValley repository catalogue...
SunnyValley repository is up to date.
All repositories are up to date.
Checking integrity... done (0 conflicting)
The most recent versions of packages are already installed


Thank you for the pkg clean suggestion, I believe that worked.

[pkg clean]

Hi,

Can you share the commands output;

pkg clean
pkg update
pkg search ubench

I have reinstalled Zenarmor but did not configure again yet because of the ubench error I got yesterday.

pkg clean output
root@router:~ # pkg clean
The following package files will be deleted:
        /var/cache/pkg/os-sunnyvalley-1.2_1~c903d6c917.txz
        /var/cache/pkg/os-sensei-1.10.1~2e63a9cffd.txz
        /var/cache/pkg/os-sunnyvalley-1.2_1.txz
        /var/cache/pkg/os-sensei-updater-1.10.txz
        /var/cache/pkg/os-sensei-1.10.1.txz
        /var/cache/pkg/os-sensei-updater-1.10~9249ba3dac.txz
        /var/cache/pkg/ubench-0.32~bbd4f2ad21.txz
        /var/cache/pkg/ubench-0.32.txz
        /var/cache/pkg/os-sensei-agent-1.10.5~f5aa1cfce9.txz
        /var/cache/pkg/os-sensei-agent-1.10.5.txz
The cleanup will free 48 MiB

Proceed with cleaning the cache? [y/N]: y

oot@router:~ # pkg update
Updating OPNsense repository catalogue...
OPNsense repository is up to date.
Updating SunnyValley repository catalogue...
SunnyValley repository is up to date.
All repositories are up to date.

pkg search ubench
ubench-0.32                    Unix Benchmark Utility for CPU(s) and memory

By the way, I hit Y to pkg clean and cleaned out the pkgs.

I got the same issue on 22.1 after I updated sunnyvalley to 1.2.1, os-sesi to 1.10.1.
So, I uninstalled and reinstalled zenarmor, while coiffuring ZI get the error  in hardware configuration "We could not locate ubench package, tried to install it, and installation did not work.".

Help pls.