1
German - Deutsch / Re: Suche Site2Site Konfiguration für div. Fritzboxen an Opensense
« on: September 07, 2022, 12:50:33 pm »
Die 7360 und 7390 sind direkt mit dem Internet verbunden oder sind noch andere Geräte dazwischen?
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
vpncfg {
connections {
enabled = yes;
conn_type = conntype_lan;
name = "Ziel-Hostname"; # Standort der Sense
always_renew = no;
reject_not_encrypted = no;
dont_filter_netbios = yes;
localip = 0.0.0.0;
local_virtualip = 0.0.0.0;
remoteip = 0.0.0.0;
remote_virtualip = 0.0.0.0;
remotehostname = "Ziel-Hostname"; # Standort der Sense
localid {
fqdn = "Mein-Hostname"; # Standort der FritzBox
}
remoteid {
fqdn = "Ziel-Hostname"; # Standort der OPNsense
}
mode = phase1_mode_aggressive;
phase1ss = "all/all/all";
keytype = connkeytype_pre_shared;
key = "Sicheres Passwort";
cert_do_server_auth = no;
use_nat_t = yes;
use_xauth = no;
use_cfgmode = no;
phase2localid {
ipnet {
ipaddr = 192.168.10.0; # (IP-Bereich Seite FritzBox)
mask = 255.255.255.0;
}
}
phase2remoteid {
ipnet {
ipaddr = 192.168.20.0; # (IP-Bereich Seite OPNsense)
mask = 255.255.255.0;
}
}
phase2ss = "esp-all-all/ah-none/comp-all/pfs";
accesslist = "permit ip any 192.168.20.0 255.255.255.0"; # IP-Bereich Seite OPNsense, Zugriffsrechte
}
ike_forward_rules = "udp 0.0.0.0:500 0.0.0.0:500",
"udp 0.0.0.0:4500 0.0.0.0:4500";
}
// EOF
Hmm, the swap dialog was hidden because it was decided to make auto-install as snappy as possible. seeing zfs being squeezed into tiny systems we might as well make the swap dialog get in the way of every zfs install, likely to the disadvantage of people avoiding the swap partition altogether.
While a swap file can be used, a swap file cannot hold a crash dump. This is what matters...
Ah ja, danke, ich lese gerade, dass Swap-Dateien generell nicht von ZFS unterstützt werden. Somit sollte man sich bei der Installation entscheiden, ob man eine Swap-Partition anlegen will oder nicht.Du verwechselst da was. Eine Swap-Datei innerhalb des ZFS sollte man nicht verwenden. Eine Swap-Partition außerhalb von ZFS dagegen sehr wohl. Ich würde eine von 2-4 GB Größe anlegen.
Memory usage: 24 % (1005/4035 MB)
SWAP usage: 0 % (0/8192 MB)
Disk usage:
15% / [zfs] (911M/6.0G)
1% /boot/efi [msdosfs] (1.8M/260M)
0% /tmp [zfs] (652K/5.1G)
0% /zroot [zfs] (96K/5.1G)
0% /var/mail [zfs] (136K/5.1G)
0% /var/audit [zfs] (96K/5.1G)
0% /usr/ports [zfs] (96K/5.1G)
5% /var/log [zfs] (291M/5.4G)
0% /var/tmp [zfs] (96K/5.1G)
0% /usr/src [zfs] (96K/5.1G)
0% /usr/home [zfs] (96K/5.1G)
0% /var/crash [zfs] (96K/5.1G)
0% /var [tmpfs] (36M/11G)
0% /tmp [tmpfs] (200K/11G)
http[s]://[v6.]sync.afraid.org/u/[zufällig generierter Hash pro Hostname]/