Home
Help
Search
Login
Register
OPNsense Forum
»
English Forums
»
General Discussion
»
Opnsense and Proxmox error
« previous
next »
Print
Pages: [
1
]
Author
Topic: Opnsense and Proxmox error (Read 686 times)
DukeFL
Newbie
Posts: 4
Karma: 0
Opnsense and Proxmox error
«
on:
June 05, 2024, 01:18:22 pm »
I have Opnsense in a VM in Proxmox.
The VM runs fine WITHOUT any VLAN tags but, I need to enter a VLAN tag and I get a QEMU error exit code 1.
I have tried to enable QEMU in the options tab of the VM and tried to load QEMU into the VM itself which I cant seem to do.
There are other VM's running on my system with QEMU but, they are Debian or Ubuntu VM's.
Any ideas how I can get QEMU into Opnsense so I can add the needed VLAN tags?
Thank You,
Logged
cookiemonster
Hero Member
Posts: 1823
Karma: 95
Re: Opnsense and Proxmox error
«
Reply #1 on:
June 05, 2024, 01:31:08 pm »
qemu is an emulation technology, you can't "get it into Opnsense". It's not a package or somesuch.
You can make a virtual network device vlan aware in proxmox's VM settings or you can handle the vlan setup in the settings of the interface inside Opnsense.
Perhaps you can tell what you need to achieve to give a more specific pointer.
Logged
DukeFL
Newbie
Posts: 4
Karma: 0
Re: Opnsense and Proxmox error
«
Reply #2 on:
June 06, 2024, 12:59:30 am »
Thanks for your reply...
I attached what info I could find.
Please Note:
enxaa81173088e9 is my USB LTE modem
enp6s0f0 and enp6s0f1 are two RJ45 ports on a PCI card
enp3s0 is the built in RJ45 on my motherboard (which I'm not using at the moment)
It sounds so easy but it's not.
The internet comes in through my USB LTE modem and goes through Opnsense and passed out the two RJ45's on the PCI card.
Thanks for any help,
Logged
cookiemonster
Hero Member
Posts: 1823
Karma: 95
Re: Opnsense and Proxmox error
«
Reply #3 on:
June 06, 2024, 03:09:05 pm »
that setup looks fine. What tells you that you need to use a VLAN tag?
If you put the tag on the OPN VM on the Proxmox settings, then OPN is unaware of it. It behaves as a client in an access port.
Logged
DukeFL
Newbie
Posts: 4
Karma: 0
Re: Opnsense and Proxmox error
«
Reply #4 on:
June 13, 2024, 04:51:03 pm »
Hello Again,
I was trying to follow a online YouTube video which suggested the vlan tags.
I have since watched more videos and done more reading and I do now have Opnsense running inside Proxmox.
Now I have two other questions and I'm sure they are some stupid mistake I made.
1. I notice that both my WAN and LAN have a 192 ip address.
My LTE modem does use a 192.168.0.1 LAN ip address and I think it has it's own DCHP inside.
2. Two LAN ports on my PCI card are 2.5gb but, they don't show up that way.
Please see the two new file attachments.
Any help/ideas would be appreciated.
Thank You,
Logged
Print
Pages: [
1
]
« previous
next »
OPNsense Forum
»
English Forums
»
General Discussion
»
Opnsense and Proxmox error