NAT before IPSEC tunnel, not working?

Started by jesperfr, August 15, 2019, 07:44:32 AM

Previous topic - Next topic
Is this still a problem ?

I need to NAT an address before sending it through an IPSEC tunnel, but I can't get it to work. According to packet capture it seems that NAT is done, but it's not being tunneled afterwards.

Rgds,
Jesper

Most of it should be fixed in 19.7.2
WWW: www.routerperformance.net
Support plans: https://www.max-it.de/en/it-services/opnsense/
Commercial Plugins (German): https://opnsense.max-it.de/

I litle more explanation
It's an existing tunnel, My end 10.222.0.0/16 remote end 10.1.204.0/24
I have a server in my end coming from 10.220.2.72 which I translate to 10.222.8.4. If I ping from the local server and do a packet capture on WAN interface , then I can see the translated addr. towards the server I try to reach (10.1.204.108).

firewall interfaces:
VLAN 10 (10.220.0.9/22
VLAN 32 (10.222.8.4/22)
WAN

My local server is comming via VLAN 10 and is being translated to interface addr. on VLAN 32.

please find attached a packet capture . Ping done from a server 10.220.2.13 and it's being translated to 10.222.8.4, but the packet towards 10.1.204.108 is not being tunneled.

I have tried to do 2 configs. Both configs are outbound nat

WAN as outgoing interface (packet capture WAN)
IPSEC as outgoing interface (packet capture IPSEC)

PACKET CAPTURE WAN:
VLAN10
em0   09:29:01.766196 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32194, offset 0, flags [none], proto ICMP (1), length 60)
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43537, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43538, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43539, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43540, length 40
VLAN10
em0   09:29:06.475942 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32195, offset 0, flags [none], proto ICMP (1), length 60)
VLAN10
em0   09:29:11.465461 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32196, offset 0, flags [none], proto ICMP (1), length 60)
VLAN10
em0   09:29:16.475901 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32197, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:29:01.766572 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32194, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1
10.222.8.4 > 10.1.204.108: ICMP echo request, id 8203, seq 43537, length 40
10.222.8.4 > 10.1.204.108: ICMP echo request, id 8203, seq 43538, length 40
10.222.8.4 > 10.1.204.108: ICMP echo request, id 8203, seq 43539, length 40
10.222.8.4 > 10.1.204.108: ICMP echo request, id 8203, seq 43540, length 40
WAN
em1   09:29:06.476327 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32195, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:29:11.465774 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32196, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:29:16.476087 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32197, offset 0, flags [none], proto ICMP (1), length 60)


PACKET CAPTURE IPSEC:
VLAN10
em0   09:36:51.695292 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32198, offset 0, flags [none], proto ICMP (1), length 60)
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43547, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43548, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43549, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43550, length 40
VLAN10
em0   09:36:56.466359 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32199, offset 0, flags [none], proto ICMP (1), length 60)
VLAN10
em0   09:37:01.483428 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32200, offset 0, flags [none], proto ICMP (1), length 60)
VLAN10
em0   09:37:06.466768 00:26:0a:27:d6:00 > 00:50:56:a8🇩🇪54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32201, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:36:51.695470 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32198, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43547, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43548, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43549, length 40
10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 43550, length 40
WAN
em1   09:36:56.466440 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32199, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:37:01.483573 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32200, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:37:06.466915 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32201, offset 0, flags [none], proto ICMP (1), length 60)

in below image, test is 10.220.2.13 - Salling group is 10.1.204.108 - VLAN32_NAT_INTERFACE is 10.222.8.4

Screenshots Phase2 SA please
WWW: www.routerperformance.net
Support plans: https://www.max-it.de/en/it-services/opnsense/
Commercial Plugins (German): https://opnsense.max-it.de/

A ping from firewall VLAN32 interface (10.222.8.4) work, but when I use same interface address or any other address in 10.222.0.0/16 for translation, then I can't ping

Errr .. did you follow the binat guide from official docs? Cant see any Screenshot of binat rules. It wont work like this
WWW: www.routerperformance.net
Support plans: https://www.max-it.de/en/it-services/opnsense/
Commercial Plugins (German): https://opnsense.max-it.de/

August 19, 2019, 09:21:25 AM #7 Last Edit: August 19, 2019, 09:51:29 AM by jesperfr
I have tried both 1:1 NAT and outbound NAT, but neither work.

Packet capture with BI NAT rule:
VLAN10
em0   09:49:14.273478 00:26:0a:27:d6:00 > 00:50:56:a8:de:54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32211, offset 0, flags [none], proto ICMP (1), length 60)
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46613, length 40
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46614, length 40
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46615, length 40
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46616, length 40
VLAN10
em0   09:49:19.207255 00:26:0a:27:d6:00 > 00:50:56:a8:de:54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32212, offset 0, flags [none], proto ICMP (1), length 60)
VLAN10
em0   09:49:24.206931 00:26:0a:27:d6:00 > 00:50:56:a8:de:54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32213, offset 0, flags [none], proto ICMP (1), length 60)
VLAN10
em0   09:49:29.206841 00:26:0a:27:d6:00 > 00:50:56:a8:de:54, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 127, id 32214, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:49:14.273756 00:50:56:a8:47:5c > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Ethernet (len 6), IPv4 (len 4), Request who-has 10.1.204.108 tell 91.221.51.240, length 28
WAN
em1   09:49:14.274354 00:26:0a:27:d6:00 > 00:50:56:a8:47:5c, ethertype ARP (0x0806), length 60: Ethernet (len 6), IPv4 (len 4), Reply 10.1.204.108 is-at 00:26:0a:27:d6:00, length 46
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46613, length 40
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46614, length 40
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46615, length 40
    10.220.2.13 > 10.1.204.108: ICMP echo request, id 1, seq 46616, length 40
WAN
em1   09:49:14.274394 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32211, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:49:19.207418 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32212, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:49:24.207103 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32213, offset 0, flags [none], proto ICMP (1), length 60)
WAN
em1   09:49:29.206921 00:50:56:a8:47:5c > 00:26:0a:27:d6:00, ethertype IPv4 (0x0800), length 74: (tos 0x0, ttl 126, id 32214, offset 0, flags [none], proto ICMP (1), length 60)

And you added the internal source IP to SPD in IPsec Phase2?
WWW: www.routerperformance.net
Support plans: https://www.max-it.de/en/it-services/opnsense/
Commercial Plugins (German): https://opnsense.max-it.de/

No, nothing have have been added to SPD in phase2. As I previously mentioned, I don't have access to remote end, and remote end is not an Opnsense firewall.

What IP do I need to add? and should this be done in both end of the tunnel ?

Again, did you read the binat guide? You have to add SPD in Phase 2 like described in the howto. It's the source IP/net you used as in 1to1 nat
WWW: www.routerperformance.net
Support plans: https://www.max-it.de/en/it-services/opnsense/
Commercial Plugins (German): https://opnsense.max-it.de/

Yes, I did read the how to BINAT, but I thought I had to add the network/host in both end of the tunnel and that was not an option.

I got it to work now. Thanks very much for all your help, it's highly appreciated :o)

Glad you did it  8)
WWW: www.routerperformance.net
Support plans: https://www.max-it.de/en/it-services/opnsense/
Commercial Plugins (German): https://opnsense.max-it.de/