Messages

We're having issue's with one router where Windows client's are not receiving their leases:

Code Select Expand


May 7 09:56:03 dhcpd: DHCPACK to 10.xx.yy.77 (80:fa:5b:57:11:18) via igb1
May 7 09:56:03 dhcpd: DHCPINFORM from 10.xx.yy.77 via igb1
May 7 09:56:03 dhcpd: DHCPACK on 10.xx.yy.77 to 80:fa:5b:57:11:18 via igb1
May 7 09:56:03 dhcpd: DHCPREQUEST for 10.xx.yy.77 (10.xx.yy.1) from 80:fa:5b:57:11:18 via igb1
May 7 09:56:03 dhcpd: DHCPOFFER on 10.xx.yy.77 to 80:fa:5b:57:11:18 via igb1
May 7 09:56:03 dhcpd: DHCPDISCOVER from 80:fa:5b:57:11:18 via igb1


Windows only get's himself a 169 IP and if reboot into Linux I see the same log entry but Linux set the correct IP. As this is over several Windows machines I don't have a clue what this is about...

Just upgraded four of my machines to 18.1.1 and it seems as the problem persist's...

+1 for me

just installed a new machine yesterday where I added igb1 & igb2 to a bridge and created a new LAN from that.

To answer my own question:

Issue was with "manual Outbound NAT" went back to "Automatic outbound NAT" and it works now as expected...

Hi Guys,

what's the status of this issue. I'ld like to move on with... ;-)

On a newly installed machine (based on an APU1) I see the following issue:

Code Select Expand

opnsense: /services_dyndns_edit.php: Aborted IP detection: Failed to connect to checkip.dyndns.org port 80: Operation timed out

And I'm not sure why I saw the same message with this host too: dynupdate.no-ip.com Which BTW makes way more sense as I'm using NoIP...


And yes I'm aware of:
https://forum.opnsense.org/index.php?topic=4727.0
and
https://forum.opnsense.org/index.php?topic=4114.0

Greetz
Mircsicz

THX for the heads up Franco...

I've setup a normal installation and checked the boxes for the RAMdisks.

Serial is yet untested on the machine... But would be good/nice to have ;-)

Seen the two checkboxes, I'll probably stick to that as a fast fix!

But what could it be that after the reboot renders the system unbootable?!? The resize of the image is running fine, had it attached to a TrueOS Machine for file manipulation. It's a 8GB as the SD ...

As I'm more used to grub I can't really deal with the loader prompt, but I'm pretty sure the solution can't be that far away.

THX a ton

Hi Franco,

sadly same same... :-(

In the meantime I had created a standard install from the vga image to the SD, did all the config's and it ran smooth.

So the question on top of my head is: Is it possible to convert a normal setup into a nanoBSD installation? So the SD survive longer than half a year...

Greetz
Mircsicz

I've an older Model of https://www.dsm-computer.de/products-solutions/products/systems/din-rail-pc/din-rail-pc-h1-a3.html which I'ld like to reuse as a router in the family...

I've flashed OPNsense-17.7.5-OpenSSL-nano-i386.img to a SD and successfully booted for the first time, assigned interface and so on. Then I rebooted and ended up with a unbootable system:

can't load kernel

was the message I was facing

I've tried tried to deal with it at the prompt. Been setting currdev & rootdev, even set it in loader.conf on SD directly. but that didn't change the behaviour...

Here are some screenshot's:

so loaddev and currdev show a different slice than lsdev, is that OK or the maybe the reason?



So if anyone has a clue why the hack it doesn't load the kernel I'ld be very grateful

They enter the LAN, so LAN should be fine ...

But I've added access list entry's for each of the subnet's so that should work for you too! ;-)

@Franco

If you wanna have access to a bunch of machines suffering from the issue just let me know... ;-)

BTW: I'm the one who triggered the whole topic, as I've just started using pfMon with some of my machines.

Greetz
Mircsicz

They're definitly different. APU2 has USB3, APU1 not...

I'll check tomorow night if it will solve the

Code Select Expand


WARNING - Timeout at ehci_wait_td:517!
ehci pipe=0x000eee80 cur=000efdc0 tok=801f0c81 next=1 td=0x0000fdc0 status=1f0c80
USB transmission failed


problem which appeared on the two APU 1C4 I've from a client. Tried it four times since tuesday, upon first reboot the above error stop's the show.

All tested with OPNsense-17.7.5-OpenSSL-nano-amd64.img.bz2

Greetz
Mircsicz

Hi Franco,

I had the same prob on 2 APU 1C4 on latest OPNsense-17.7.5-OpenSSL-nano-amd64.img.bz2 with this issue:

Code Select Expand


WARNING - Timeout at ehci_wait_td:517!
ehci pipe=0x000eee80 cur=000efdc0 tok=801f0c81 next=1 td=0x0000fdc0 status=1f0c80
USB transmission failed


I did install "os-boot-delay" pkg and had the following in loader.conf.local:

Code Select Expand


kern.cam.boot.delay=10000


Greetz
Mircsicz