Messages

1

General Discussion / cloudflare tunnel over GRE

« on: August 13, 2024, 05:27:21 am »

how do I install the cloudflared service on opensense and be able to establish a tunnel with cloudflare?

I did found this guide: https://www.jackpearce.co.uk/cloudflared-opnsense/

after the installation I coudn't find this folder: cd /usr/ports/security/cloudflared

2

General Discussion / VIP Address

« on: June 04, 2024, 06:10:10 pm »

Hello Folks,

I am using a VM in Google Cloud and I have only one Public German IP address 34.x.x.x that points to the internal VM private IP 10.x.x.10

I am thinking to set a Virtual public IP in Opnsense that I will get from Google that has to face the external hosts.

I would like to know:

- if I get the public IP from Google can I set it as a Virtual IP and use it for outbound NAT?

- if the virtual IP is Italian and my VM is in Germany region can it still works?

my Idea is the face the external hosts with an Italian IP even if the VM is located in Germany. any Ideas?


Thank you!

3

General Discussion / Re: New openvpn interface and socks proxy

« on: May 11, 2024, 08:08:30 pm »

well, this will force me to just leave opnsense and use Linux instead! thanks for the clarification and good luck!

4

General Discussion / Re: New openvpn interface and socks proxy

« on: May 11, 2024, 06:59:06 am »

did you solved?
I can still see the OpenVPN advanced settings windows after the update. I don't know why you shouldn't see it.
did you tried to add the directive in the OpenVPN server config file? does it gets reset after reboot?

5

General Discussion / pipe delay issue

« on: April 21, 2024, 09:13:12 pm »

Hello folks,
I did created 2 pipes 1 for download and 1 for upload.
I can control the bandwidth separately without any issue, i.g down 10mbps and up 5mbps. the issue is when I add latency to just one of the pipes let's say I add 50ms delay to the "download pipe"... also the "upload pipe" is affected.
so the result is 50ms added delay on both pipes.
down pipe [original latency + 50ms delay = 100]
up pipe [original latency + 50ms delay = 100]

this is what I am trying to do:
down pipe [original latency + 50ms delay = 100]
up pipe [original latency + no delay = 50]

6

General Discussion / Re: Force traffic to be forwarded to a specific Vlan

« on: February 13, 2024, 05:56:02 pm »

I would like to set the MTU on the VLAN and never change it. that VLAN must handle a certain type of traffic that's it.
I don't have any idea why you did mentioned DMZ in this case, I would appreciate it if you explain more.

7

General Discussion / Force traffic to be forwarded to a specific Vlan

« on: February 13, 2024, 04:17:02 pm »

Hello Folks,

if I have a Wan and a Vlan, the Vlan Is configured with a static IP and DHCP server.

Is there a way to make the Traffic coming from outside to be redirected straight to the Vlan? than from the Vlan can go to the destination?


the main reason I need this is to make the traffic flow and get different MTU values from both of them, e.g udp mtu 1280, while tcp mtu is 576. apparently there is no way to set the MTU based on he traffic with only one Interface.

Thanks!

8

Virtual private networks / force Wireguard traffic to flow between Vlans

« on: February 12, 2024, 03:01:48 pm »

I have a wan, wireguard tunnel and 2 Vlans (Vlan01 tagged 10, Vlan02 tagged 20).
these 2 Vlans are configured with static IPs.

Is there a way to make Wireguard's Tunnel use these two Vlans than the traffic will exit these two Vlans and go back to the destination through the WAN? some sort of loadbalancing...

the main reason I need this is to make the traffic flow and get different MTU values from both of them, e.g udp mtu 1280, while tcp mtu is 576.

all the Vlan's are using the same gateway of the wan (not specified): Dynamic.

Thanks!