1
Hardware and Performance / Re: Bad performance with VLAN
« on: March 08, 2022, 07:23:45 pm »
As no one seems able to help out, would I make more out of my router just getting rid of the VLAN setup?
Pros/Cons?
Pros/Cons?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General Discussion / Re: UDP Broadcast Relay
« on: March 07, 2022, 04:48:38 pm »
I'm unable to start the service. It indicates that it's loading (Please wait pop up), then nothing happens. I'm fairly new to OpnSense, so I'm not quite sure where to look for errors or what might be wrong. 
I'm trying to set it up for Chromecast.
Versions OPNsense 22.1.2_1-amd64
FreeBSD 13.0-STABLE
OpenSSL 1.1.1m 14 Dec 2021
Edit: Turns out port was in use. Solved it. Now it's "green" and running, but still can't get it to work. Not sure if I did the Firewall correct.
I'm trying to set it up for Chromecast.Versions OPNsense 22.1.2_1-amd64
FreeBSD 13.0-STABLE
OpenSSL 1.1.1m 14 Dec 2021
Edit: Turns out port was in use. Solved it. Now it's "green" and running, but still can't get it to work. Not sure if I did the Firewall correct.
3
Hardware and Performance / Re: Bad performance with VLAN
« on: February 20, 2022, 07:16:18 am »If the two endpoints on the two VLAN's you've tested the throughput between are both connected via a single vlan trunk, ~450Mbit would be expected ?
Also, with the Intel interfaces on that board, it may be worth trying the setting:
Interfaces:Settings:Disable VLAN hardware filtering
(Note that for this to take effect, it's currently necessary to configure and enable the untagged igb interfaces as an 'Interface', even if you don't plan to use it.)
Versions OPNsense 22.1-amd64
FreeBSD 13.0-STABLE
OpenSSL 1.1.1m 14 Dec 2021
Yes, I'm on fiber.
I've changed the settings following this: https://teklager.se/en/knowledge-base/opnsense-performance-optimization/
And my VLAN is having my LAN as parent, I believe. I'm still kind of new to OpnSense.
4
Hardware and Performance / Bad performance with VLAN
« on: February 14, 2022, 12:03:43 pm »
Hi!
I'm running a APU3D4 Board (4 core, 1Ghz/1.4Ghz CPU, 4 GB ECC DDR3-1333 DRAM, 3 x Gbit ports) with a 1 GB connection.
After being in touch with the reseller support at Teklager, he's been able to throughput 1 GB, or at least close to.
I'm unable to achieve anything above 450~ Mbit/s, and we've manage to pinpoint that the problem seems to be with me running a few (3) VLAN.
Does anyone know of some tweak which would allow a bit more throughput? 1 GB isn't quite necessary (but it would be nice). However, I'd be happy to get at least 600+ and keeping my VLANs if possible.
I'm running a APU3D4 Board (4 core, 1Ghz/1.4Ghz CPU, 4 GB ECC DDR3-1333 DRAM, 3 x Gbit ports) with a 1 GB connection.
After being in touch with the reseller support at Teklager, he's been able to throughput 1 GB, or at least close to.
I'm unable to achieve anything above 450~ Mbit/s, and we've manage to pinpoint that the problem seems to be with me running a few (3) VLAN.
Does anyone know of some tweak which would allow a bit more throughput? 1 GB isn't quite necessary (but it would be nice). However, I'd be happy to get at least 600+ and keeping my VLANs if possible.
5
Tutorials and FAQs / Re: [Tutorial] How I do port forwarding - simple and straightforward
« on: November 08, 2021, 12:14:16 pm »
This post solved my 3-day headache. THANKS! <3 NAT Reflection did the trick..
Pages: [1]