Messages

1

Zenarmor (Sensei) / Re: OPNsense upgrade failure with Zenarmor (23.1.7)

« on: May 24, 2023, 02:03:59 am »

@rfc805, @almodovaris, @TritonB7

Can you reach out to Zenarmor support? Use the "Bug Report" screen on the upper right hand corner of the screen - in case you're not familiar.

Make sure you send all OPN/Zenarmor config and logs.

This looks pretty much like another netmap thing. We want to investigate further.

Thanks.

I did submit a Bug Report earlier this month along with config and logs. I'm using an Intel x550-t2 and i350t4v2, same issue with both cards.

2

Zenarmor (Sensei) / Re: OPNsense upgrade failure with Zenarmor (23.1.7)

« on: May 18, 2023, 04:55:05 pm »

I am running into a similar issue. Out of curiosity, what type of interface/nic are you using?

3

Zenarmor (Sensei) / Re: Reports - Block, session detail shows Loaded records: 0 / 0

« on: April 07, 2022, 01:16:57 am »

Ran into the same issue on my end, except I'm on OPNsense 22.1.4_1. Reinstalling resolved the issue.

4

22.1 Legacy Series / Re: errors and strange behavior opnsense 22.1.1_1

« on: February 18, 2022, 12:41:24 am »

@Franco
After trying by trial and error a lot of things I found in Suricata this error:
Stats for 'igb0^': pkts: 0, drop: 0 (nan%), invalid chksum: 0

I did a google, found an old opnsense forum mentioning something about setting Suricata  Pattern matcher from hyperscan (what I use on my opnsense Intel(R) Core(TM) i5-7500 CPU @ 3.40GHz (4 cores, 4 threads)
changed it to Aho-Corasick
saved and than the weird stuff ended, all working as should... but again.. after just some minute(s) all strange things are back.

changed the setting back to Hyperscan,
saved and than the weird stuff ended again, all working as should. but again, after just some minute(s) strange things as described started again.

So I think with my trial and error, it seems related to Suricata? Or changing config in Suricata refreshes "something" in opsense what "solves" the problem for some minutes....

Hope this helps the searching direction...

I'm having similar errors, but I'm not using Suricata. I am using Zen Armor though for LAN.

5

Virtual private networks / DHCP Relay across Site-to-Site VPN

« on: July 23, 2021, 04:39:32 am »

Has anyone succesffuly done this? If so, would you be able to provide your particular setup or guide? I'm currently using WireGuard between two sites, but when trying to use DHCP relay on SiteB's OPNsense router to send DHCP requests to SiteA. However, when relaying request to a SiteA IP, I get the following error in the log's and the DHCP relay service fails to start:

"Unsupported device type 131 for "wg0""

6

Virtual private networks / Wireguard to VPN Provider and Multiple Peers

« on: June 25, 2021, 04:18:48 am »

I'm following the documentation found here:

https://docs.opnsense.org/manual/how-tos/wireguard-selective-routing.html


In Step2, can I select multiple endpoints? If so, how does this behave in regards to how traffic is routed to each of the endpoints etc or if an endpoint is down.

7

General Discussion / Different Traffic Graph Widgets on Two Routers running OPNsense 21.1.7

« on: June 25, 2021, 12:29:54 am »

Hello,

I have two physical servers with OPNsense 21.1.7 installed. The traffic graph widget looks different for each server. Server 1 shows all the interfaces toggles on the graph itself. Server 2 shows a dropdown with the ability to check/uncheck the interfaces. Can someone explain why I would get different traffic graph widget options between these two installs?

Server1 hardware:
Motherboard: A2SDi-8C+-HLN4F IX2 being used for WAN and IX3 being used for Trunk
Additional NIC: Intel x550-T2 IX0 being used for OPT1 (nothing connected to this port yet)

Server2 hardware: X10SDV-TP8F
Motherboard: X10SDV-TP8F with IGB2 (i350) being used for WAN
Additional NIC: Chelsio T520-CR with CXL0 being used for Trunk