Messages

1

24.1 Legacy Series / Console outputs frequently 'vm_fault: pager read error'

« on: March 03, 2024, 09:24:52 am »

On console, I'm seeing a lot these:

<SNIP>
vm_fault: pager read error, pid 70868 (rrdtool)
vm_fault: pager read error, pid 70868 (rrdtool)
vm_fault: pager read error, pid 70868 (rrdtool)
vm_fault: pager read error, pid 70868 (rrdtool)
</SNIP>

RRDtool seems to be working fine, and graphs are also working.

2

23.7 Legacy Series / Re: Lots of messages about aborted python processes

« on: March 02, 2024, 01:22:35 pm »

Expirencing the same in a freshly installed opnsense.  non-virtuel

3

Virtual private networks / Re: Why is the IPSec service not showing up at VPN -> IPSec -> Tunnel settings

« on: June 10, 2023, 04:41:42 pm »

Never mind..   Need to enable IPSec in VPN-> IPSec -> Tunnel settings... 

4

Virtual private networks / Re: Why is the IPSec service not showing up at VPN -> IPSec -> Tunnel settings

« on: June 10, 2023, 04:09:44 pm »

This is the new install.......

5

Virtual private networks / Why is the IPSec service not showing up at VPN -> IPSec -> Tunnel settings

« on: June 10, 2023, 03:55:46 pm »

Got this fresh OPNSense installed, and updated..   After install, I was adding IPSec config, but the service does not seem to be found.   Usually when looking at VPN -> Tunnel Settings.  You have the ability to stop/start/restart the service..  On this new install..  Seems to be missing

6

Virtual private networks / Missing 'Remote network" on GUI when trying to define phase2

« on: March 08, 2022, 12:26:49 pm »

Got a new firewall installed, and trying to get an IPsec s2s between two OPNsense.

So - In gui. Local network appears just fine, but the remote-network is nowhere to be seen under the phase 2 config.

What am I missing??

7

General Discussion / IPv6/IPv4 usage ratio stats

« on: December 22, 2021, 11:03:17 am »

Is there a simple way of getting the IPv4/IPv6 traffic ratio out/inbound on eg. WAN interface. Using any tools native to the OpnSense installation??

Other than downloading the netflows for external processing?

/Nykaer

8

General Discussion / Re: OPN as a PXE boot server

« on: September 24, 2021, 10:53:16 am »

Following.    Been meaning to get something like this running at home.

I'll start and report back any findings.

/Nykaer

9

General Discussion / Re: Unbound: Bulk add host-entries (overrides)

« on: April 23, 2021, 06:13:39 pm »

That would work just fine..  Sold.

Thank you for the solution.

10

General Discussion / Unbound: Bulk add host-entries (overrides)

« on: April 23, 2021, 04:48:21 pm »

I have quite a few host overrides I need to enter into our OPNsense.

Looked at the API, and I does not include these entries.  I could manually enter them into /var/unbound/cat host_entries.conf.   But according to docs, that will not survive a reboot.

Any ideas, before I spends hours "cURL'ing my way out of the problem??

/Nykaer

11

20.7 Legacy Series / Re: opnsense freezes and needs reboot

« on: February 02, 2021, 08:57:43 am »

Seems to be solved on my environment now.
On VMware ESXi 6.7U3.

Interfaces -> Settings: Enabled all hardware offloading + VLAN hardware filtering.

The last part seemed to do the trick, and have been running for more than 48 hours now.  Before I needed to reboot every 6-10 hours or so..