Messages

change "hw.syscons.kbd_reboot" to 1 (default is 0 = on)
(System > Settings > Tunables)

[...]
pkg install -fy os-sensei
[...]

i updated today to 24.1.7 and zenarmor 1.17.2 at the same time, is it recommend to do this or am i fine?
It is currently running fine without any logbook records.

from day one wit my current ISP i have this setting:
Physical NIC: 1512
PPoE vlan: 1508
WAN: 1500

this was working until the 23.7 release. didn't change anything with it.
after upgrade to 23.7.5 and a reload of WAN, MTU is now working again at 1500, without changing any configuration.
so, for me its works fine, Thnx OPNsense Team! ;D

it's in netmap, not suricata.
Suricata and Zenarmor use netmap

IDS means, its only detecting it, not blocking.
Blocking only happens with IPS..

IPS: intrusion prevention system
IDS: intrusion detection system

i don't know if you need to enabled it, but on my system its enabled and Suricata works fine on a PPPoE connection

hoe heb je Lan ingesteld? deze staat op track interface en die staat weer ingesteld op Wan?
OPNsense kan overigens ook gewoon rechtstreeks op KPN glasvezel worden aangesloten, kun je de draak van een v10A ook weer in de doos proppen ;)

IPS doesn't work with PPPoE, Only IDS works.

under: > System > Settings ? Administration. then change the 'Listen Interfaces' under Web GUI and Secure Shell

i had the same problem, after changing VLAN Hardware Filtering from Disabled to Default and reboot its working again.
hardware checksum offload was already disabled.

i use PPPoE with vlan on a intel nic with IX driver

Thanks for chiming in on the wrong issue. I have to reiterate that this isn't helpful.


Cheers,
Franco

if this is the wrong issue, which one is the right?
today i found out that when i change the Router Advertisements from 'managed' to 'assisted' my desktop is getting a fully working IPv6, were on 'managed' it only got the ipv6 dns server info but no working ipv6 connection...
i would love to help, but i have no clue were to start ::)

21.1.5 broke my ipv6 config.
when untick the 'Allow manual adjustment of DHCPv6 and Router Advertisements', my desktop is getting an ipv6 address, but this will break my android phone wifi connection...
also, when ssh into opnsense wan/pppoe is showing a ipv6 address what is in use by one of the lans.
the GUI dashboard is showing a fe80 address...

before 21.1.4 everything was fine!

logbook is showing this:

Code Select Expand


2022-04-08T17:48:13 Error opnsense /usr/local/etc/rc.newwanipv6: On (IP address: 2XXX:XXXX:XXXX:1:92e2:XXXX:fe0e:3874) (interface: WAN[wan]) (real interface: pppoe1).
2022-04-08T17:48:13 Error opnsense /usr/local/etc/rc.newwanipv6: IPv6 renewal is starting on 'pppoe1'
2022-04-08T17:48:12 Error opnsense /interfaces.php: Warning! dhcpd_radvd_configure(auto) found no suitable IPv6 address on igb0
2022-04-08T17:48:12 Error opnsense /interfaces.php: Warning! dhcpd_radvd_configure(manual) found no suitable IPv6 address on ix0_vlan9
2022-04-08T17:48:12 Error opnsense /interfaces.php: Warning! dhcpd_radvd_configure(manual) found no suitable IPv6 address on ix0_vlan1337
2022-04-08T17:48:12 Error opnsense /interfaces.php: Warning! dhcpd_radvd_configure(manual) found no suitable IPv6 address on mlxen0
2022-04-08T17:48:12 Error opnsense /interfaces.php: Warning! dhcpd_dhcp6_configure() found no suitable IPv6 address on opt5
2022-04-08T17:48:12 Error opnsense /interfaces.php: Warning! dhcpd_dhcp6_configure() found no suitable IPv6 address on opt6
2022-04-08T17:48:12 Error opnsense /interfaces.php: ROUTING: skipping IPv6 default route
2022-04-08T17:48:12 Error opnsense /interfaces.php: ROUTING: IPv6 default gateway set to wan
2022-04-08T17:48:12 Error opnsense /interfaces.php: ROUTING: skipping IPv4 default route
2022-04-08T17:48:12 Error opnsense /interfaces.php: ROUTING: IPv4 default gateway set to wan
2022-04-08T17:48:12 Error opnsense /interfaces.php: ROUTING: entering configure using 'opt7'


logbooks are bit bit broke, the dhcp4 logbook is empty, but going from the syslogbook widget from the desktop i can get more... had the change the filter options to show everything...

I, too, have a PPPoE internet connection, and I'm having the same issues with IPV6 sometimes working and sometimes not. I noticed that the ssh/terminal screen shows different info than the GUI dashboard, as can be seen in the screenshots. Could this be related?

i have the same thing after i swap the Intel x540T2 for a Intel x520 SR, wan pppoe has the same ipv6 ip as one of the local lan networks, for me its currently using my pi-hole vlan what resulting in weird dns issues.
when turn off the pi-hole network interface, wan pppoe got an another ipv6 address from one of the enabled lan networks...
can't put the x540 back in because its broken...

before the swap it was just a fe80 address like the gui is showing... (which works create!)

well i found out that you cant use a 1.10 backup... zenarmor is telling me the backup is to old, version 0.
guess i have to do a fresh start :-X

after installing 'os-sunnyvalley', you have to install 'os-sensei' to get Zenarmor installed.

"os-sunnyvalley" is the repository where "os-sensei" is Zenarmor...