Messages

1

Documentation and Translation / Re: AdGuard Home setup guide

« on: July 13, 2023, 12:01:54 am »

Anyone update today from the web admin page, then have the service not be able to start?

*edit*
Ended up deleting the plug in and re-installing.

2

23.1 Legacy Series / Adguard Updated, won't start

« on: July 12, 2023, 11:27:59 pm »

Adguard Home is installed on my OPNSense box.  Was working fine.  AdGuard prompted for an update via the admin website.  It started, then never came back.  Now the service is showing stopped in OPNsense and won't started.  System has been rebooted, no change.

3

Documentation and Translation / Re: AdGuard Home setup guide

« on: July 02, 2023, 04:45:34 pm »

What does the "Primary DNS" tick box do?

4

General Discussion / Re: Backup: Nextcloud configuration

« on: November 21, 2021, 01:54:55 am »

I've registered just to add this:

I had the same "Cannot get real username" error, but in my case I was already using an FQDN and a trusted Letsencrypt cert.

The root cause for me was that the directory I chose already existed, and the solution was to remove that directory in NC and then re-run the "Setup/Test" again. Doing so, the test succeeded and the directory was created and populated with a single XML backup on my NC server.

I'm back working on this.  This still returned the same error for me in the logs. 

My NC instance is running on an UnRaid server (docker) and uses SWAG (letsencrypt) for the reversely proxy and cents.  Both machines are on the same subnet.

5

Documentation and Translation / Re: AdGuard Home setup guide

« on: October 17, 2021, 03:55:32 pm »

My ISP provides IPv6 addresses.  When I enable that on OPNSense it also directs DNS via IPv6.  Is there a good guide to follow to explain how to use IPv6 in a home environment and still use PIHole/Adguard for filtering?  For now I just disabled IPv6.

6

General Discussion / Re: Backup: Nextcloud configuration

« on: March 12, 2021, 01:33:11 am »

I think I’m having the same issue.  I’ve tried w/ both my actual username/password and the application specific generated credentials.  Here are the relevant logs

2021-03-11T19:26:40   config[36701]   {"url":"https:\/\/nextcloud.willsisti.com\/ocs\/v1.php\/cloud\/user","content_type":null,"http_code":0,"header_size":0,"request_size":0,"filetime":-1,"ssl_verify_result":0,"redirect_count":0,"total_time":60.00686,"namelookup_time":0.000374,"connect_time":0,"pretransfer_time":0,"size_upload":0,"size_download":0,"speed_download":0,"speed_upload":0,"download_content_length":-1,"upload_content_length":-1,"starttransfer_time":0,"redirect_time":0,"redirect_url":"","primary_ip":"","certinfo":[],"primary_port":0,"local_ip":"","local_port":0,"http_version":0,"protocol":0,"ssl_verifyresult":0,"scheme":"","appconnect_time_us":0,"connect_time_us":0,"namelookup_time_us":374,"pretransfer_time_us":0,"redirect_time_us":0,"starttransfer_time_us":0,"total_time_us":60006860}   
2021-03-11T19:26:40   config[36701]   Cannot get real username

7

Development and Code Review / Re: Installed sensei - webinterface not working anymore

« on: March 01, 2021, 04:48:51 am »

Was there a fix for this issue.  I've got the same problem.

8

Intrusion Detection and Prevention / Installed Sensei - Lost access to web front end

« on: March 01, 2021, 04:45:33 am »

I followed the documentation to install sensei, but after it was done I lost connection to the OPNSense web admin panel.  I can't ssh in either. Ping responds, but Safari/Chrome do not.  I'm running OPNSense on a dell SFF.  i5-4570, 8gb, and intel i350-T4 network card.  Using 2 ports one for WAN and one LAN.  I do have a VLAN set for a guest wifi network (Aruba AP) and a Cisco L3 switch. 

9

Development and Code Review / Re: mdns-repeater

« on: December 13, 2020, 02:27:30 am »

I was using this plug in to enable my chrome casts to live on my untrusted VLAN while being able to cast from my trusted VLAN.  Recently stopped working, I can see the devices, but no music will play.  Only real changes I made were OPNSense updates.  Anyone else have issues?

10

Hardware and Performance / Re: Newbie Here - Will this hardware be sufficient for Gig Speed?

« on: June 25, 2020, 06:58:44 pm »

Which i5?


Sent from my iPhone using Tapatalk

11

Hardware and Performance / Using OPNSense for WireGuard server on Dell Wyse 3040 - Intel Atom Z8350

« on: June 25, 2020, 04:25:29 pm »

Thinking of using a Dell Wyse 3040 (Intel Atom Z8350) as a cheap and easy to deploy WireGuard server for about 10 users to access a file server when not at the office. Is that a viable use case for a OPNSense install. Just one NIC with a static IP on the clients LAN.

Thanks
Will