Messages

I apologize for the delay, ended up in meetings all day yesterday. Here is the link to get it:

https://www.dropbox.com/s/xasw9wz8vmdv7yf/OPNSense_19_1_4.zip?dl=0

It will expire in 15 days. I did the following:

Gen 2 VM (Secure Boot Off)
2x vCPU
3GB of RAM
32GB of HDD (SCSI 0:0)
2x vNIC

Installed 19.1.4 (image I had laying around) using Guided Install method and GPT/UEFI for disk. Default login.
I did test it by putting an IP on the LAN interface and hooking it up to my test network. It passed traffic and worked. I then reset it all to factory defaults using the console menu.

Hopefully that helps!

Thank You so much but that too didnt work :(

Pfsense is using FreeBSD 11.2, whereas OPNsense is using 'Hardened FreeBSD' 11.2 https://hardenedbsd.org/

I believe some components are removed from a standard FreeBSD kernel when creating a Hardened BSD build in an attempt to reduce the possible attack surface among other things.
If you're on the latest supported BIOS and firmware then it might be a request to the Hardened BSD team to see what is going on.

OPNsense and Hardened BSD have a pretty close relationship from what I understand, so hopefully one of their team can help with getting you past this boot error.

Edit: You could try downloading HBSD 11.2 and booting that up in Hyper-V 2019. See if it fails at the same point. This would point to either OPNsense or HBSD as being the issue.

This seemed to point to the cause thou, the Hardened BSD also didnt install and kept going the same way. Have send a mail to the develeopers over at Hardened BSD hope they can help :(

What version of Hyper-V are you running? I have installed OPNSense on 2012 R2, 2016, and 2019. That all said, I did have the issue when installing 19.1 on Hyper-V 2019 where it would get stuck at selecting the install destination, but the CTRL-C would get it through that.

A thought would be to add an IDE controller and attach a HDD to that to see if that allows it through. I have other non-OPNSense BSD versions like the IDE controller better than the SCSI.

Lastly, I can build an OPNSense VM on Hyper-V, export it, and give you a link to see if it is just the install or OPNSense as a whole on your particular setup.

I have Hyper-V running on 2019. I was thinking of having a direct HDD for the VM.

I would be great if you could share a link, Can be checked if its something with the install.

Just a thought...

Do you have the latest supported BIOS for your system.
An updated Hardened FreeBSD 11.2 is used now and may require a later BIOS?
Possibly worth checking any other firmware for storage controllers etc

I have a GA-890FXA-UD5 with an AMD Phenom™ II X6.

I am running a pfSense on the same and its running fine, which makes me doubt. It is also based on FreeBSD 11.2

It seems alls going waste, Gen1 Gen2. Nothing makes a sense. Direct DVD, ISO Image or even the VGA image onto a disk doesn't do the thing. All stop right here.

Why does the install stop at the point it tries to mount root

 LAN NIC





WAN NIC





Last screen on the install process

I just didn't enable, its the same if its added too.  :-\

I used Gen 1, Installed 18.7. Worked perfectly fine till i tried to upgrade to 19.1.7 and there it went.

Tried a fresh install and still the same.

I tried on Gen 2 with secure boot disabled and below are the different stages of how that install went.

Its Gen 1.

Yup. Sorry about that. It actually 19.1. I later saw the error and posted in the other one. Just couldn't c a delete to the thread.

I am trying to setup opnsense on a hyperv and every time the install ends at the same point. I have allocated 32 GB HDD and 3 GB RAM, 2 Virtual processors as well.

I tried to install 18.7 and upgrade to 19.1. 18.7 went fine and I was able to do ten initial config. Once I did the upgrade it went back to the same thing.

I am trying to setup opnsense on a hyperv and every time the install ends at the same point. I have allocated 32 GB HDD and 3 GB RAM, 2 Virtual processors as well.