"
I am running an up to date version of OpnSense with ZenArmor installed. When I try to access ZenArmor Dashboard I get a spinning circle signifying an attempt to open. Patience is not paying off and nothing seems to happen even after several minutes (10+). As I am unable to access the gui is there any command line suggestions to try?
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
Hardware and Performance / Re: Speed throughput
November 11, 2023, 06:34:31 PM
Welcome all. Glad to see this discussion.
I have moved back to my Protectli FW4A-0 running an Intel(R) Atom(TM) CPU E3845 @ 1.91GHz (4 cores, 4 threads) with 8Gb RAM. My WAN connection is DHCP from the ISP modem (that is default setup as a bridge.) Currently I have 802 Mbps down. (Not to concerned with my up speed of 39.6 Mbps.)
I can nbow see that my issue was hardware related and moving back to the FW4A-0 has resolved my dissatifaction.
Thanks erveybody. Your thought helped me. (I consider my part of this decision closed.)
I have moved back to my Protectli FW4A-0 running an Intel(R) Atom(TM) CPU E3845 @ 1.91GHz (4 cores, 4 threads) with 8Gb RAM. My WAN connection is DHCP from the ISP modem (that is default setup as a bridge.) Currently I have 802 Mbps down. (Not to concerned with my up speed of 39.6 Mbps.)
I can nbow see that my issue was hardware related and moving back to the FW4A-0 has resolved my dissatifaction.
Thanks erveybody. Your thought helped me. (I consider my part of this decision closed.)
#3
Hardware and Performance / Speed throughput
November 10, 2023, 11:58:37 PM
My ISP provides service at 1Gb. I have tested with my laptop connected to their modem and speed reports are in the 1Gb range. Great! Enter OPNsense (23.7.8) the mimugmail repository provides a speedtest plugin. That plugin is reporting 200Mbps. When I run 'speedtest-cli' from the commend line I am getting 108.63 Mbit/s. Clearly tuning is required to improve this speed.
My OPNsense is running on a Protectli box (FW4) with an Intel(R) Celeron(R) CPU J3060 @ 1.60GHz (2 cores, 2 threads). Searching the web yields little to nothing to assist a BSD novice like myself. (Years of Linux experience and I have a touch of BSD experience however not enough for this issue I am tackling.) This is a home network not commercial. But please understand that the bottleneck appears to be OPNsense. I found this, https://binaryimpulse.com/2022/11/opnsense-performance-tuning-for-multi-gigabit-internet/ but stopped when he began discussing a 24-core cpu. And it is an article from 2022. Since then, there has been several OPNsense version upgrades. So far, I have not found any helpful info that is at home network or SOHO network level of use. Where can I find the info I need to improve my ISP speed throughput?
My OPNsense is running on a Protectli box (FW4) with an Intel(R) Celeron(R) CPU J3060 @ 1.60GHz (2 cores, 2 threads). Searching the web yields little to nothing to assist a BSD novice like myself. (Years of Linux experience and I have a touch of BSD experience however not enough for this issue I am tackling.) This is a home network not commercial. But please understand that the bottleneck appears to be OPNsense. I found this, https://binaryimpulse.com/2022/11/opnsense-performance-tuning-for-multi-gigabit-internet/ but stopped when he began discussing a 24-core cpu. And it is an article from 2022. Since then, there has been several OPNsense version upgrades. So far, I have not found any helpful info that is at home network or SOHO network level of use. Where can I find the info I need to improve my ISP speed throughput?
Pages1
