1
Hardware and Performance / OPNSense on Netgate SG-8860
« on: October 25, 2019, 05:17:33 pm »
Has anyone installed OPNSense on a Netgate SG-8860? If so, do you have any instructions on how to install it?
TIA!
TIA!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General Discussion / Systemwide DNS Change
« on: February 01, 2019, 08:41:08 pm »
How do I change my system-wide DNS to https://quad9.net. I've changed it in DHCP but where else do I change it?
TIA!
TIA!
3
General Discussion / Error Message w DVD ISO on Rufus
« on: November 08, 2017, 04:39:38 pm »
I am getting an error message on Rufus when attempting to write the ISO. I did a checksum and its all good. The error I get is:
Unsupported image
This image either a non-bootable or it sues a boot or compression method that is not supported by Rufus...
When I use the VGA image .img version and use Rufus to DD the file I don't have the error at all and it works.
Anyone else see this issue?
Unsupported image
This image either a non-bootable or it sues a boot or compression method that is not supported by Rufus...
When I use the VGA image .img version and use Rufus to DD the file I don't have the error at all and it works.
Anyone else see this issue?
4
General Discussion / Re: Can't get Opnsense box not getting IP on LAN or WAN
« on: November 08, 2017, 04:05:55 pm »
Sorry this is my first experience with OPNsense so I made a mistake in previous attempts to configure it. The issues was that when configuring the interfaces I was putting using interface autoconfiguration and it wasn't working.
Is em0 supposed to be configured to be the LAN port? Because my hardware has it labeled WAN. So I manually configured the interfaces. Once I specified em0/em1 it all worked fine.
Is there a plan to add more post install configuration information to documentation?
Nice work on the project, love it so far!
Is em0 supposed to be configured to be the LAN port? Because my hardware has it labeled WAN. So I manually configured the interfaces. Once I specified em0/em1 it all worked fine.
Is there a plan to add more post install configuration information to documentation?
Nice work on the project, love it so far!
5
General Discussion / Can't get Opnsense box not getting IP on LAN or WAN
« on: November 08, 2017, 01:37:06 pm »
I'm building OPNsense on a new Protectli FW6C system. It installs fine and I do the initial configuration while disconnected (as I am using my Internet connection). I've plugged a monitor into the HDMI port and used the text setup.
Odd thing is I can't seem to get connected to the Internet or get a LAN IP. I haved tried several times to reset it and made sure it has the proper LAN DHCP scope but I get not Internet IP and no LAN IP. I'm only get APIPA addresses locally. On the monitor of my OPNsense box I see:
em0 link state changed to UP when I plug it in and down when I unplug it but still I get no IP.
I've tried to reset to the defaults and do the setup twice and it doesn't work.
Is there something I'm missing?
Thanks so much!
Odd thing is I can't seem to get connected to the Internet or get a LAN IP. I haved tried several times to reset it and made sure it has the proper LAN DHCP scope but I get not Internet IP and no LAN IP. I'm only get APIPA addresses locally. On the monitor of my OPNsense box I see:
em0 link state changed to UP when I plug it in and down when I unplug it but still I get no IP.
I've tried to reset to the defaults and do the setup twice and it doesn't work.
Is there something I'm missing?
Thanks so much!
6
Documentation and Translation / Re: Download Link doesn't specify signature
« on: November 07, 2017, 11:23:01 pm »
Cool.
Yes, I figured it out but think others would benefit.
Yes, I figured it out but think others would benefit.
7
Documentation and Translation / Download Link doesn't specify signature
« on: November 07, 2017, 05:26:37 pm »
The download link https://opnsense.org/download/
shows a signature but doesn't state what hashing algorithm is used.
It would help if it is had those details.
shows a signature but doesn't state what hashing algorithm is used.
It would help if it is had those details.
Pages: [1]