1
Chinese - 中文 / Re: 非常感谢开通中文版块！！
« on: June 23, 2015, 03:14:08 am »
希望更多的中文用户加入交流讨论哪。
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
3
General Discussion / Re: can't boot after power failer
« on: May 29, 2015, 03:37:19 pm »
Thank you chol! i will go to study it.
4
General Discussion / Re: how to set ip range?
« on: May 26, 2015, 01:56:09 am »
Thank you chol!
i means when i add a rule, for example, block a ip range outbound to internet but pass another ip range outbound to internet on the same interface, then it is not easy to set ip range, alias can't do it also, i have to add ip one by one on alias, then apply in the firewall rule.
i means when i add a rule, for example, block a ip range outbound to internet but pass another ip range outbound to internet on the same interface, then it is not easy to set ip range, alias can't do it also, i have to add ip one by one on alias, then apply in the firewall rule.
5
General Discussion / how to set ip range?
« on: May 25, 2015, 03:32:19 am »
alias, rules, etc, i can't find any place to set ip range.
who can tell me how/where to set it? Now i have to add ip singly, it need much time and easy to forget certain ip.
who can tell me how/where to set it? Now i have to add ip singly, it need much time and easy to forget certain ip.
6
General Discussion / Re: can't boot after power failer
« on: May 24, 2015, 04:34:11 pm »
smart log:
smartctl 6.3 2014-07-26 r3976 [FreeBSD 10.1-RELEASE-p10 i386] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
Warning! SMART Attribute Data Structure error: invalid SMART checksum.
=== START OF READ SMART DATA SECTION ===
Warning! SMART ATA Error Log Structure error: invalid SMART checksum.
SMART Error Log Version: 10
Invalid Error Log index = 0x08 (T13/1321D rev 1c Section 8.41.6.8.2.2 gives valid range from 1 to 5)
is it my ssd bad?
smartctl 6.3 2014-07-26 r3976 [FreeBSD 10.1-RELEASE-p10 i386] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
Warning! SMART Attribute Data Structure error: invalid SMART checksum.
=== START OF READ SMART DATA SECTION ===
Warning! SMART ATA Error Log Structure error: invalid SMART checksum.
SMART Error Log Version: 10
Invalid Error Log index = 0x08 (T13/1321D rev 1c Section 8.41.6.8.2.2 gives valid range from 1 to 5)
is it my ssd bad?
7
General Discussion / Re: can't boot after power failer
« on: May 24, 2015, 02:06:59 pm »
we use a UPS, but it only support 20 minutes, so still meet this fault.
if OPnsense will support detecting power status automatic and shutdown by itself?add watchdog on OPNsense?
Thanks!
if OPnsense will support detecting power status automatic and shutdown by itself?add watchdog on OPNsense?
Thanks!
8
General Discussion / can't boot after power failer
« on: May 24, 2015, 06:54:23 am »
Hi,
After the electricity interrupted, then restored, my OPNsense can't reboot. VGA mode, it shows: no media...
So i had to reinstall by my USB flash disk and configure lan ip, then restore configuration.
what is the reason? how can i do to prevent this failure happen again?
After the electricity interrupted, then restored, my OPNsense can't reboot. VGA mode, it shows: no media...
So i had to reinstall by my USB flash disk and configure lan ip, then restore configuration.
what is the reason? how can i do to prevent this failure happen again?
9
General Discussion / Re: About SSD install
« on: May 23, 2015, 02:53:33 am »
yes, i used 15.1.10.
I had been done as your suggestion, and apply remote log server with splunk.
Thank your work!
I had been done as your suggestion, and apply remote log server with splunk.
Thank your work!
10
General Discussion / Re: About SSD install
« on: May 21, 2015, 11:48:43 am »
Now OPNsense's status:
MBUF----30%(7856/26368)
Memory----6%(120/2005MB)
SWAP usage----0%(2048MB)
Disk usage----52%(837M/1.7G)
MBUF----30%(7856/26368)
Memory----6%(120/2005MB)
SWAP usage----0%(2048MB)
Disk usage----52%(837M/1.7G)
11
General Discussion / About SSD install
« on: May 21, 2015, 10:12:54 am »
Hi all,
Today i saw a topic 'SSD (Solid State Drive) and pfSense (Important)':
https://forum.pfsense.org/index.php?topic=34381.75
i installed OPnsense in SSD(4G), memory is 2G. What should i do to keep my router very stable?
Today i saw a topic 'SSD (Solid State Drive) and pfSense (Important)':
https://forum.pfsense.org/index.php?topic=34381.75
i installed OPnsense in SSD(4G), memory is 2G. What should i do to keep my router very stable?
13
General Discussion / [SOLVED] is it right?
« on: May 20, 2015, 02:58:09 am »
I want to set a rule on Lan interface:
at a schedule range, block some hosts access internet
so, i set:
src------alias(some hosts)
dst--------WAN net
thus set dst, is it ok? or i need set it 'any' ?
at a schedule range, block some hosts access internet
so, i set:
src------alias(some hosts)
dst--------WAN net
thus set dst, is it ok? or i need set it 'any' ?
14
General Discussion / Re: can't access web configuration
« on: May 18, 2015, 04:27:01 pm »
just now i updated it to 15.1.10.2 in shell mode, then reboot, then web configuration login is ok now!
Thanks you all!
Thanks you all!
15
General Discussion / Re: can't access web configuration
« on: May 18, 2015, 01:46:52 am »
at lease, every user can login to change password in the past.
now after i reinstalled OPNsense, then restore configuration with user info, every user account can't login, but shell can show every user's info.
now after i reinstalled OPNsense, then restore configuration with user info, every user account can't login, but shell can show every user's info.
Pages: [1] 2