smartctl -a /dev/ada0
smartctl 7.1 2019-12-30 r5022 [FreeBSD 11.2-RELEASE-p19-HBSD amd64] (local build)Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org=== START OF INFORMATION SECTION ===Device Model: SATAFIRM S11Serial Number: KCMLCCC11263554LU WWN Device Id: 0 000000 000000000Firmware Version: SBFMBBW3User Capacity: 32,017,047,552 bytes [32.0 GB]Sector Size: 512 bytes logical/physicalRotation Rate: Solid State DeviceForm Factor: mSATADevice is: Not in smartctl database [for details use: -P showall]ATA Version is: ACS-4 (minor revision not indicated)SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)Local Time is: Mon Nov 15 13:58:42 2021 CSTSMART support is: Available - device has SMART capability.SMART support is: Enabled=== START OF READ SMART DATA SECTION ===SMART overall-health self-assessment test result: FAILED!Drive failure expected in less than 24 hours. SAVE ALL DATA.See vendor-specific Attribute list for failed Attributes.General SMART Values:Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled.Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run.Total time to complete Offlinedata collection: (65535) seconds.Offline data collectioncapabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported.SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer.Error logging capability: (0x01) Error logging supported. General Purpose Logging supported.Short self-test routinerecommended polling time: ( 2) minutes.Extended self-test routinerecommended polling time: ( 30) minutes.Conveyance self-test routinerecommended polling time: ( 6) minutes.SMART Attributes Data Structure revision number: 16Vendor Specific SMART Attributes with Thresholds:ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 6438 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 13168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0170 Unknown_Attribute 0x0003 000 000 010 Pre-fail Always FAILING_NOW 335007449104173 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 131075192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 6194 Temperature_Celsius 0x0023 067 067 000 Pre-fail Always - 33 (Min/Max 33/33)218 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0231 Temperature_Celsius 0x0013 100 100 000 Pre-fail Always - 99241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 707SMART Error Log Version: 1No Errors LoggedSMART Self-test log structure revision number 1No self-tests have been logged. [To run self-tests, use: smartctl -t]SMART Selective self-test log data structure revision number 0Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testingSelective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk.If Selective self-test is pending on power-up, resume after 0 minute delay.