Slow WAN after upgrade

[jaybowee]

Hello all,

I have been testing the upgrade and found that my speed is cut in half after the upgrade. I can go back to 20.1 and it returns to normal. Has anyone else had this problem?. Some may not see it if you don't get 1gb down. Mine is 900/45 but when I upgrade I get 590/45. Clean install both versions to get the same results.

[FullyBorked]

I just noticed a similar issue, I blamed my ISP at first. 

I'm on 1Gbps/40Mbps, right after a reboot I get ~950Mbps down, after its been up a bit it drops to ~130Mbps down and it's always that cap for some reason.  It's happened every boot for me now. 

[falk]

Hi,

I have the same issue with my 500/500 connection.
After the update I get ~280M up/down.

I guess that my hw are getting over the edge with this update.

But when doing a iperf3 one of the cores gets bogged down on 100%.
```
  PID USERNAME    PRI NICE   SIZE    RES STATE    C   TIME    WCPU COMMAND
0 root        -76    -      0   288K CPU1     1   3:13 100.00% [kernel{if_io_tqg_1}]
```

--
Regards Falk

[FullyBorked]

Hi,

I have the same issue with my 500/500 connection.
After the update I get ~280M up/down.

I guess that my hw are getting over the edge with this update.

But when doing a iperf3 one of the cores gets bogged down on 100%.
```
  PID USERNAME    PRI NICE   SIZE    RES STATE    C   TIME    WCPU COMMAND
0 root        -76    -      0   288K CPU1     1   3:13 100.00% [kernel{if_io_tqg_1}]
```

--
Regards Falk

Mine isn't CPU related, I rarely even see over 40% util.  My load averages are usually around 0.15.  I'm not sure what's causing the slowdown on my system.  I'm on brand new hardware as well.

[jaybowee]

Well I went back to the previous version. Can't take a 400 mb hit like that. My cpu is 2.4 ghz 8 cores and runs under 10% so something is up with the latest version.

[ascii]

i have the same.
when i disable scricata i get my 1GBit back.
with scricata enabeld it dorps so ~600MBit

[banym]

Hello,

please always mention if you are using IPS/IDS or Proxy.
It is a total different setup if you make use of that technology or if you are just doing Firewalling/NAT.

The speed and throughput can differ depending on configuration and active ruleset of any IPS/IDS.

Share details so others can verify your setup with their setups.

Regards,

Dominik

[FullyBorked]

Hello,

please always mention if you are using IPS/IDS or Proxy.
It is a total different setup if you make use of that technology or if you are just doing Firewalling/NAT.

The speed and throughput can differ depending on configuration and active ruleset of any IPS/IDS.

Share details so others can verify your setup with their setups.

Regards,

Dominik

Fair point, I'm using IPS, my speeds seem fine even with IPS for a bit then it degrades to near nothing.  Seemed ok before 20.7 not sure if its the Suricata update or what.

Sent from my GM1917 using Tapatalk

[falk]

Hello,

please always mention if you are using IPS/IDS or Proxy.
It is a total different setup if you make use of that technology or if you are just doing Firewalling/NAT.

The speed and throughput can differ depending on configuration and active ruleset of any IPS/IDS.

Share details so others can verify your setup with their setups.

Regards,

Dominik

I don't use proxy, ips/ids or anything strange, just normal FW/NAT.

With 20.1 the performance of the hw was just on the limit, but in 20.7 it bogs the cpu almost at half the speed.

```
CPU: Intel(R) Atom(TM) CPU D525 @ 1.80GHz (2 cores)
NIC: 82583V Gigabit Network
MEM: 4G
```

--
Regards Falk

[jaybowee]

Like I said. Clean install on both versions. Everything default and the issue remains.

[mfpck]

same here  :(

[FullyBorked]

Can't seem to locate the source for the WAN slowdown.  I disabled IPS and tried a download and I still can't get over 120-130 Mbps on a gigabit connection.  If I reboot the box I can get ~950Mbps for a short time, then it falls back down.  CPU and RAM usage very low.  So strange and frustrating. 

[jaybowee]

Exactly my problem as well.

[Mondmann]

Hello All,
Test the energy management setting once
on Hightadaptive! All others reduce the transfer rates to about 50%.
Greetings from Germany

[FullyBorked]

Hello All,
Test the energy management setting once
on Hightadaptive! All others reduce the transfer rates to about 50%.
Greetings from Germany

Thanks for the idea, I've been in hiadaptive.  Wonder if setting to max might help. 

Grüße aus den USA (best I can do ;) )