Dashboard not showing correct WAN public IP address using PPPOE

[franco]

> Can I get an ifconfig with the right and wrong address included?

Nevermind, it eventually reads ifconfig which is wrong in numerous edge cases.

I'll put this on my list.


Cheers,
Franco

[franco]

FYI https://github.com/opnsense/core/issues/7707

[machare]

If I ping the correct public IP address I get a reply.

How do you know that the reply is coming from your router and not someone else's? What do you get if you visit https://ip4.me/ ?

One reason is that it is a fixed IP address.  It has been the same address for a few years.

[machare]

I think we might be conflating issues here. The OP claims that they have a static *IPv4* address assigned by PPPoE, and that the WebUI is showing a different *IPv4* address. This seems quite different from seeing only a link-local IPv6 addresses (which may be a separate issue).

Yes, sorry - wrong thread. There was another issue with someone seeing only a link-local address in the dashboard widget.

Does this help:
492
        description: OPT1 (opt1)
        options=4802028<VLAN_MTU,JUMBO_MTU,WOL_MAGIC,HWSTATS,MEXTPG>
        ether 20:7c:14:a2:04:40
        inet6 fe80::227c:14ff:fea2:440%igb0 prefixlen 64 scopeid 0x1
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igb1: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1500
        description: LAN (lan)
        options=4802028<VLAN_MTU,JUMBO_MTU,WOL_MAGIC,HWSTATS,MEXTPG>
        ether 20:7c:14:a2:04:41
        inet 10.0.1.139 netmask 0xffffff00 broadcast 10.0.1.255
        inet6 fe80::227c:14ff:fea2:441%igb1 prefixlen 64 scopeid 0x2
        media: Ethernet autoselect (1000baseT <full-duplex>)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igb2: flags=1008843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1500
        description: OPT2 (opt2)
        options=4802028<VLAN_MTU,JUMBO_MTU,WOL_MAGIC,HWSTATS,MEXTPG>
        ether 20:7c:14:a2:04:42
        inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
        inet6 fe80::227c:14ff:fea2:442%igb2 prefixlen 64 scopeid 0x3
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igb3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=4802028<VLAN_MTU,JUMBO_MTU,WOL_MAGIC,HWSTATS,MEXTPG>
        ether 20:7c:14:a2:04:43
        media: Ethernet autoselect
        status: no carrier
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
lo0: flags=1008049<UP,LOOPBACK,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 16384
        options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
        groups: lo
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0 metric 0 mtu 1536
        options=0
        groups: enc
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
pfsync0: flags=0 metric 0 mtu 1500
        options=0
maxupd: 128 defer: off version: 1400
        syncok: 1
        groups: pfsync
pflog0: flags=20100<PROMISC,PPROMISC> metric 0 mtu 33152
        options=0
        groups: pflog
pppoe0: flags=10088d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST,LOWER_UP> metric 0 mtu 1484
        description: WAN (wan)
        options=0
        inet 80.229.30.223 --> 195.166.130.254 netmask 0xffffffff
        inet6 fe80::227c:14ff:fea2:440%pppoe0 prefixlen 64 scopeid 0x9
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
ovpnc1: flags=1008051<UP,POINTOPOINT,RUNNING,MULTICAST,LOWER_UP> metric 0 mtu 1500
        options=80000<LINKSTATE>
        inet 10.0.8.2 --> 10.0.8.1 netmask 0xffffffff
        inet6 fe80::227c:14ff:fea2:440%ovpnc1 prefixlen 64 scopeid 0xa
        groups: tun openvpn
        nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
        Opened by PID 41940
wg1: flags=10080c1<UP,RUNNING,NOARP,MULTICAST,LOWER_UP> metric 0 mtu 1420
        options=80000<LINKSTATE>
        inet 10.0.7.2 netmask 0xfffffff0
        groups: wg wireguard
        nd6 options=103<PERFORMNUD,ACCEPT_RTADV,NO_DAD>
wg2: flags=10080c1<UP,RUNNING,NOARP,MULTICAST,LOWER_UP> metric 0 mtu 1420
        options=80000<LINKSTATE>
        inet 10.0.9.1 netmask 0xfffffff0
        groups: wg wireguard
        nd6 options=103<PERFORMNUD,ACCEPT_RTADV,NO_DAD>
machare@OPNsense:~ $

[franco]

Thanks. The issue seems clear now. It's fixed in the development version but I can't provide an easy fix as this required a number of commits, backend command restart and JS update in order to work as expected. It will be  shipped in 24.7.1.


Cheers,
Franco

[machare]

@franco
Thank you, it is only a cosmetic issue. I am glad that the PPPoE itself still works as it was quite difficult to do this originally.

[franco]

True. PPPoE has never been easy.


Cheers,
Franco

[nodakbarnes]

So while I figured this was an issue for me as well it turns out it may just be a misunderstanding.

The default widget showing the WAN interface is called Gateways.

What I needed to see my ISP supplied public address was the Interfaces widget.

Once I loaded that widget it showed the proper WAN address on my PPPoE connection.

That raises the question on choice of default widgets...doesn't interfaces seem more appropriate for most users than Gateways?