update from 22.7 install image to 22.7.4 leads to AHCI timeouts and errors

[Catalin]

HI.

Opnsense installed from official image - 22.7. Setup, config, startup - no problems, no errors.

first thing update after config wizard, reboot then getting long time startup and errors:

ahci0: <AHCI SATA controller> port 0x3090-0x3097,0x3080-0x3083,0x3060-0x307f mem 0x80800000-0x80801fff,0x80803000-0x808030ff,0x80802000-0x808027ff at device 23.0 on pci0
ahci0: AHCI v1.31 with 1 6Gbps ports, Port Multiplier not supported
ahcich1: <AHCI channel> at channel 1 on ahci0
ada0 at ahcich1 bus 0 scbus0 target 0 lun 0
ahcich1: Timeout on slot 26 port 0
ahcich1: is 00000000 cs 00000000 ss 04000000 rs 04000000 tfd 50 serr 00000000 cmd 0000c917
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 3 more tries remain
ahcich1: Timeout on slot 14 port 0
ahcich1: is 00000000 cs 00000000 ss 00004000 rs 00004000 tfd 40 serr 00000000 cmd 0000ce17
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 2 more tries remain
ahcich1: Timeout on slot 19 port 0
ahcich1: is 00000000 cs 00000000 ss 00080000 rs 00080000 tfd 40 serr 00000000 cmd 0000d317
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 1 more tries remain
ahcich1: Timeout on slot 24 port 0
ahcich1: is 00000000 cs 00000000 ss 01000000 rs 01000000 tfd 40 serr 00000000 cmd 0000d817
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 0 more tries remain
ahcich1: Timeout on slot 29 port 0

any ideas? thanks

[axsdenied]

Couple of things;

1. I would find it odd that going from 22.7 to 22.7.4 would introduce this issue unless there were kernel changes that I'm unaware of. I looked through the patch notes and didn't see anything suggesting it, but I could have missed it.

2.  It's possible it's just a coincidence and the source of the issue is something else.

Either way; What kind of hard drive do you have? What mode is your drive set to in the Bios? AHCI, ATA, RAID?

[dinguz]

I would start by ruling out hardware issues, is it possible to run some kind of hardware diagnostics on this machine?