Startup of OPNSense or FreeBSD takes about 7 minutes

[mvdheijkant]

I did a few re-installs when I started using OPNsense and one after since and every time after the second or third reboot, the startup took more time than the 1 or 2 minutes I was expecting. During the startup I can see the timeouts as shown below. These look like the cause of the slow startups. It might not be something in OPNsense itself but more a hardware setup problem.
OPNsense is running on this hardware https://www.amazon.nl/dp/B09PHGWPMB

Does anyone have a suggesting what hardware setup could be the cause of this problem, or maybe some driver problem?

lo0: link state changed to UP
igc0: link state changed to DOWN
igc1: link state changed to DOWN
igc0: link state changed to UP
igc1: link state changed to UP
ahcich1: Timeout on slot 9 port 0
ahcich1: is 00000000 cs 00000000 ss 00000200 rs 00000200 tfd 50 serr 00000000 cmd 0000d517
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 3 more tries remain
ahcich1: Timeout on slot 26 port 0
ahcich1: is 00000000 cs 00000000 ss 04000000 rs 04000000 tfd 40 serr 00000000 cmd 0000da17
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 2 more tries remain
ahcich1: Timeout on slot 31 port 0
ahcich1: is 00000000 cs 00000000 ss 80000000 rs 80000000 tfd 40 serr 00000000 cmd 0000df17
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 1 more tries remain
ahcich1: Timeout on slot 4 port 0
ahcich1: is 00000000 cs 00000000 ss 00000010 rs 00000010 tfd 40 serr 00000000 cmd 0000c417
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 0 more tries remain
ahcich1: Timeout on slot 9 port 0
ahcich1: is 00000000 cs 00000000 ss 00000200 rs 00000200 tfd 40 serr 00000000 cmd 0000c917
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Error 5, Retries exhausted
pflog0: permanently promiscuous mode enabled
WARNING: attempt to domain_add(netgraph) after domainfinalize()

[Patrick M. Hausen]

Disk drive, cable or controller broken. Definitely a hardware problem.