Intel i225/i226 2.5G NIC Information/Issue Tracking Thread

[BrandyWine]

Did updating 226-V firmware helped to resolve connection issues?
All 5 my adaptors are currently on ver. 2.22 and I'm not sure it's worth to update...
I'm just started to test OPNsense on a new box and have experienced a few times LAN port stopped responding and needed to change the port(in a lan-bridge) to reconnect.

I had read v2.17 is where all the issues are. I am not sure yet how far past v2.17 is good, v2.32 is available. I mentioned in another thread, if Intel took time & effort to build new firmware, then they didn't do it for no reason. Also see the "Intel i226 Firmware" thread.

Can you post some data for your igc 226-V

1) pciconf -lV
2) dmesg |grep igc

[blackie333]

pciconf -lV

OK, you can see the commands results below (selected lines only)

Code Select Expand

1) pciconf -lV
igc0@pci0:2:0:0:        class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x125c subvendor=0x8086 subdevice=0x0000
igc1@pci0:4:0:0:        class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x125c subvendor=0x8086 subdevice=0x0000
igc2@pci0:5:0:0:        class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x125c subvendor=0x8086 subdevice=0x0000
igc3@pci0:6:0:0:        class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x125c subvendor=0x8086 subdevice=0x0000
igc4@pci0:7:0:0:        class=0x020000 rev=0x04 hdr=0x00 vendor=0x8086 device=0x125c subvendor=0x8086 subdevice=0x0000

2) dmesg |grep igc
[1] igc0: <Intel(R) Ethernet Controller I226-V> mem 0x81100000-0x811fffff,0x81200000-0x81203fff at device 0.0 on pci2
[1] igc0: EEPROM V2.22-0 eTrack 0x80000371
[1] igc1: <Intel(R) Ethernet Controller I226-V> mem 0x80e00000-0x80efffff,0x80f00000-0x80f03fff at device 0.0 on pci4
[1] igc1: EEPROM V2.22-0 eTrack 0x80000371
[1] igc2: <Intel(R) Ethernet Controller I226-V> mem 0x80b00000-0x80bfffff,0x80c00000-0x80c03fff at device 0.0 on pci5
[1] igc2: EEPROM V2.22-0 eTrack 0x80000371
[1] igc3: <Intel(R) Ethernet Controller I226-V> mem 0x80800000-0x808fffff,0x80900000-0x80903fff at device 0.0 on pci6
[1] igc3: EEPROM V2.22-0 eTrack 0x80000371
[1] igc4: <Intel(R) Ethernet Controller I226-V> mem 0x80500000-0x805fffff,0x80600000-0x80603fff at device 0.0 on pci7
[1] igc4: EEPROM V2.22-0 eTrack 0x80000371

[10] igc3: link state changed to UP
[101] igc3: link state changed to DOWN
[101] igc3: promiscuous mode enabled
[101] igc2: promiscuous mode enabled
[101] igc0: promiscuous mode enabled
[104] igc3: link state changed to UP


[BrandyWine]

That's odd output for that 226-V device. Showing a 2MB etid.
I need to look further. You can try flashing the 2.32 2MB to one of your unused 226's if you have unused. If it flashes in ok then you have 2MB version. If not then try the 1MB version of the bin.