Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - imWACCo

#1
It's fixed, had to power cycle the modem. I'm an old vet, had to ask a friends kid to come over and climb under the desk.
#2
Quote from: Patrick M. Hausen on December 13, 2024, 03:41:38 PMBut does the ping work after the fix? If it doesn't you need to get your WAN connection working above anything else.

No, still can't Ping. Any ideas on how to do that? I'm a hardware guy, networking is out of my skillset.
If you have any links I should be reading....
#3
Quote from: Patrick M. Hausen on December 13, 2024, 11:50:41 AMCan you ping anything (e.g. 8.8.8.8) from the firewall itself?

If that output in your first post is from the OPNsense and not from a client system behind it, then your WAN link is not configured correctly. I suggest to contact your ISP again if that is the case.

Before the OPNsense can "ping 8.8.8.8" you don't need to care about anything else (like DNS, NAT, ...) - that one MUST work first.

Quote from: peterwkc on December 13, 2024, 02:09:12 PMTry ping from the firewall itself ping 1.1.1.1 and ping www.google.com
Yes, the ping is from inside OPNsense. I got the right port "ro0", see FIX1 in OP.
#4
Quote from: DEC670airp414user on December 13, 2024, 11:47:20 AMinterfaces > overview.

are the status plugs green, as in showing corrected?

system > settings > general >  plugin a dns server like 9.9.9.9 and see if it helps

Ok, this is going to be long...
9.9.9.9 did not help

I don't see any color in interfaces > overview
What I do see:
WAN Status up

DHCP

DHCPv4 up DHCPv6 up

MAC address d4:xx:xx:xx:xx:d5 - Micro-Star Int'l Co, Ltd

MTU 1500

IPv4 address 205.xx.xx.xxx/22

IPv4 gateway : 205.xxx.xxx.1

IPv6 link-local fe80::xxxx:xxxx:xxxx:5ad5/64

IPv6 address

DNS servers 8.8.8.8 8.8.4.4

Media 1000baseT <full-duplex>

In/out packets 8377 / 83 (614 KB / 9 KB)

In/out packets (pass) 0 / 83 (0 bytes / 9 KB)

In/out packets (block) 628547 / 0 (8 KB / 0 bytes)

In/out errors 0 / 0

Collisions 0WAN Status up

DHCP

DHCPv4 up DHCPv6 up

MAC address d4:xx:xx:xx:xx:d5 - Micro-Star Int'l Co, Ltd

MTU 1500

IPv4 address 205.xx.xx.xxx/22

IPv4 gateway : 205.xxx.xxx.1

IPv6 link-local fe80::xxxx:xxxx:xxxx:5ad5/64

IPv6 address

DNS servers 8.8.8.8 8.8.4.4

Media 1000baseT <full-duplex>

In/out packets 8377 / 83 (614 KB / 9 KB)

In/out packets (pass) 0 / 83 (0 bytes / 9 KB)

In/out packets (block) 628547 / 0 (8 KB / 0 bytes)

In/out errors 0 / 0

Collisions 0
====================================================================================
LAN Status up

MAC address 00:xx:xx:xx:xx:88 - Intel Corporate

MTU 1500

IPv4 address 192.168.1.1/24

IPv6 address

Media 1000baseT <full-duplex>

In/out packets 27113 / 31115 (1.88 MB / 12.91 MB)

In/out packets (pass) 27113 / 31115 (1.88 MB / 12.91 MB)

In/out packets (block) 0 / 0 (0 bytes / 0 bytes)

In/out errors 0 / 0

Collisions 0

Interrupts

irq device total rate

irq32 igb0:rxq0 46726 5

irq33 igb0:rxq 117839 2

irq34 igb0:aq 12 0
#5
I'm looking at Firewall: NAT right now. I don't know how it should look... how can I tell if it's wrong???


Firewall: NAT: Port Forward

The only thing I'm seeing is the Anti-Lock-Out, nothing else.

There's nothing saying WAN<-->LAN, or WAN-->LAN or WAN<--LAN

Also, nothing in One-to-One, Outbound has two Loopback, NTP6 is blank
#6
Just figured out how to get OPNsense on a Lenovo, why do you need "Lenovo Fix"?!? Sorry, I have to name and shame.

Anyway, I can reach it, and it's handing out IP to other systems on the network (DNS with some static).
My ISP can see it through the modem.
But any attempt to get on the web times out.

I even did a reset just incase. Did not change any settings, just [Next] on all of them

# /sbin/ping -4 -c '3' '8.8.8.8'
PING 8.8.8.8 (8.8.8.8): 56 data bytes

--- 8.8.8.8 ping statistics ---
3 packets transmitted, 0 packets received, 100.0% packet loss
ping: sendto: No route to host
ping: sendto: No route to host
ping: sendto: No route to host

WAN is on igb1, the MoBo NIC This was wrong, it should be ro0, see FIX1


I don't know what other info you need

EDIT: System: Gateways: Single only has IPV6. I tried copying that and putting IPV4, but can't get it to run

EDIT2: System: Routes: Status

ipv6 $NUMBER link#2 U NaN 1500 igb1 wan

There's no IPV4 equivalent for WAN.

FIX1: When I System: Configuration: Defaults it sets WAN as igb1, not as I set it ro0. Still not fixed, and can't ping, but getting an IP now.
#7
Tutorials and FAQs / I'm in non-live setup phase
April 27, 2024, 11:40:48 PM
I have PfSense already*, in the process of getting a better PC with OPNsense.

Right now, it's sitting on my workbench with IP 192.168.1.137, no WAN NIC. I'm looking at a few guides for best practices. Get everything set-up, then deploy... Robert's your father's brother!

Until I get to Firmware:
***GOT REQUEST TO CHECK FOR UPDATES***
Currently running OPNsense 24.1 at Sat Apr 27 17:14:51 EDT 2024
Fetching changelog information, please wait... fetch: https://pkg.opnsense.org/FreeBSD:13:amd64/24.1/sets/changelog.txz: Host does not resolve
Updating OPNsense repository catalogue...
pkg: https://mirror.wdc1.us.leaseweb.net/opnsense/FreeBSD:13:amd64/24.1/latest/meta.txz: No address record
repository OPNsense has no meta file, using default settings
pkg: https://mirror.wdc1.us.leaseweb.net/opnsense/FreeBSD:13:amd64/24.1/latest/packagesite.pkg: No address record
pkg: https://mirror.wdc1.us.leaseweb.net/opnsense/FreeBSD:13:amd64/24.1/latest/packagesite.txz: No address record
Unable to update repository OPNsense
Error updating repositories!
pkg: Repository OPNsense cannot be opened. 'pkg update' required
Checking integrity... done (0 conflicting)
Your packages are up to date.
***DONE***


What settings do I need to have it use WAN for update?


*The system I had at the time, the PCI is limiting the NIC to 100mb on a 1gb fiber
#8
General Discussion / Will not load after install
April 05, 2024, 06:25:59 PM
I've tried both UFS|ZFS from OPNsense-23.1-OpenSSL-vga-amd64.img Install goes thru the motions, looks like it should work, but will not boot after restart.
MX Linux will install, so I ass-u-me it's not the hardware.

BIOS reset to defaults

Hardware:
ThinkCentre Edge 72
500gb HHD
4gb RAM
Realtek RTL8111E, and Intel PRO/1000 PT Server Adapter Series (not installed yet)