Messages

1

General Discussion / Re: Just trying to block a port

« on: October 05, 2024, 04:58:31 pm »

I'm trying a different approach. Remove the NAS form the iotnetwork vlan Thant way it need to go through OPNsense and in Opnsense open de Portainer port using the source iotnetwork (10.1.20.5) to the management network (10.1.1.3). I'm not sure if it's the best way but I will try it. Thank You

2

General Discussion / Re: Just trying to block a port

« on: October 05, 2024, 02:45:24 am »

Yes that's exactly what I'm trying to do client 10.1.20.x can't access the 10.1.20.3:9443. Do you know where can I blocked? Thank you

3

General Discussion / Just trying to block a port [SOLVED]

« on: October 04, 2024, 09:43:16 pm »

Hi, I have an iotnetwork vlan I add my NAS to this vlan just so I can make backups to home assistant but in this NAS I'm running docker with other services for example portainer that runs on port 9443 I try every single way to block it but it don't work. Here are my firewall rules. I already try different orders but nothing.

4

Hardware and Performance / Re: media: Ethernet autoselect is not negotiating the speed

« on: February 19, 2024, 05:24:36 pm »

Thank you. Sadly this Mac mini is older only have thunderbolt 1 and there is no adapter that run at 2.5Gb. I ended up installing Openwrt and the adapter works at full speed.

5

Hardware and Performance / Re: media: Ethernet autoselect is not negotiating the speed

« on: February 18, 2024, 06:01:06 am »

you could try the os-realtek-re plugin

try it with same results

6

Hardware and Performance / media: Ethernet autoselect is not negotiating the speed

« on: February 17, 2024, 09:54:56 pm »

After moving my OPNsense from VM to a MacMini Late 2012 I'm having issues with the ue0 USB to Ethernet adapter (I know is not recommended but the Mini only have one ethernet port) This is what I got so far any idea what could be causing the issue its the Realtek drivers or something like that. The Lan port is working but very slow if I do an Internet speed in the OPNsense I get the correct speed 850 MBps but the clients connected to the Lan port only max to 200Mbps.

Code: [Select]

bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
description: WAN (wan)
options=80088<VLAN_MTU,VLAN_HWCSUM,LINKSTATE>
ether 0c:4d:e9:b2:23:8b
inet 71.179.258.721 netmask 0xffffff00 broadcast 71.179.225.721
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL>
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0<> metric 0 mtu 1536
groups: enc
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
pflog0: flags=20100<PROMISC,PPROMISC> metric 0 mtu 33160
groups: pflog
pfsync0: flags=0<> metric 0 mtu 1500
syncpeer: 0.0.0.0 maxupd: 128 defer: off
syncok: 1
groups: pfsync
ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
description: LAN (lan)
options=80008<VLAN_MTU,LINKSTATE>
ether 80:3f:5d:f3:a4:00
inet 10.1.10.1 netmask 0xffffff00 broadcast 10.1.10.255
inet6 fe80::823f:5dff:%ue0 prefixlen 64 scopeid 0x6
inet6 2600:4040:29f2:b800 prefixlen 64
media: Ethernet autoselect
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>

Code: [Select]

ugen0.2: <Realtek USB 10/100/1G/2.5G LAN> at usbus0, cfg=2 md=HOST spd=SUPER (5.0Gbps) pwr=ON (64mA)
ugen0.2.0: cdce0: <CDC Communications Control>

Code: [Select]

ue0: <USB Ethernet> on cdce0
ue0: Ethernet address: 80:3f:5d:f3:a4:00
ue0: link state changed to UP
arp: 10.1.10.4 moved from e4:5f:01:5f:b3:b9 to 26:84:63:91:56:02 on ue0
arp: 10.1.10.4 moved from 26:84:63:91:56:02 to e4:5f:01:5f:b3:b9 on ue0
Any idea what could be causing this issue?