Messages

Hi Boris

That is the roule made by the NAT

no it is not a cisco box, but as far as i have read, the BSD 10.X have a problem with ufs and fsck that zfs do not have in the same extend.
or maby it is possible to have a double file system, one witch will be copied to active on boot, as i have seen it it is not the config file that gets corrupted but the OS.....
But But But..... i am NOT a developer i am just an idea person and as the subject suggest this is about wishes....

Well Supermule That might be the easy fix.... BUT ...... USERS...... it is a router and most users just disconnect the power if they think that something is wrong, like if it was a netgear, cisco, asus og any other kind of router....

We can have a lot of wishes, but the highest wish from me is a stable system, a system that do not crash when a power outage happens..
except from that i'll support all of the other suggestions.

no luck :-(

I tried to NAT 12345 to 192.168.1.1 without any FW Rules but the one for NAT.
Then I tried to NAT to 127.0.0.1. Still no luck :-(

try setting Register Expires to 120 on the phones, i do not know that phone but it works with a SPA112.

Hi

I have a bit of a problem with my 3/4G modems, when it have been without connection and the signal return then the LCP have closed the interface and i have to active reinitialize the device.

Code Select Expand

Jun  8 05:59:51 OPNsense ppp: [opt1] IPV6CP: SendConfigReq #50
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] LCP: no reply to 1 echo request(s)
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: parameter negotiation failed
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: state change Req-Sent --> Stopped
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: LayerFinish
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: parameter negotiation failed
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: state change Req-Sent --> Stopped
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: LayerFinish
Jun  8 05:59:53 OPNsense ppp: [opt1] Bundle: No NCPs left. Closing links...
Jun  8 05:59:53 OPNsense ppp: [opt1] Bundle: closing link "opt1_link0"...
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] Link: CLOSE event
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] LCP: Close event
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] LCP: state change Opened --> Closing
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] Link: Leave bundle "opt1"
Jun  8 05:59:53 OPNsense ppp: [opt1] Bundle: Status update: up 0 links, total bandwidth 9600 bps
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: Close event
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: state change Stopped --> Closed
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: Close event
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: state change Stopped --> Closed
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: Down event
Jun  8 05:59:53 OPNsense ppp: [opt1] IPCP: state change Closed --> Initial
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: Down event
Jun  8 05:59:53 OPNsense ppp: [opt1] IPV6CP: state change Closed --> Initial
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] LCP: SendTerminateReq #10
Jun  8 05:59:53 OPNsense ppp: [opt1_link0] LCP: LayerDown
Jun  8 05:59:55 OPNsense ppp: [opt1_link0] LCP: SendTerminateReq #11
Jun  8 05:59:57 OPNsense ppp: [opt1_link0] LCP: state change Closing --> Closed
Jun  8 05:59:57 OPNsense ppp: [opt1_link0] LCP: LayerFinish
Jun  8 05:59:58 OPNsense ppp: [opt1_link0] Link: DOWN event
Jun  8 05:59:58 OPNsense ppp: [opt1_link0] LCP: Down event
Jun  8 05:59:58 OPNsense ppp: [opt1_link0] LCP: state change Closed --> Initial



Status --> Interfaces --> Connect Does help, but it is not the right way to do it

I'll try that Monday.
Of course I'll will make a restriction that only allow a few trusted IP adresses

Me2 Me2  8) :o

I got it all configured, i got WAN, WWAN and a BRIDGE with LAN and WIRELESS, I got internet connection through the BRIDGE, so all is working fine.... except that i need to be able to access the WUI from the WAN..
some of the errors i found at pfsense i have not found here YET...... hope not to find them at all....

I'd like to access the WebGUI from the webinterface but can't get it to work

Does anyone know how to get it to work?
(Just installed my box yesterday, came from PfSense)