1
German - Deutsch / Re: Opnsense 22.1.2 Install - APU2E0
« on: August 13, 2022, 10:29:51 pm »
Hab heute ein APU aufgesetzt mit Rufus kein Problem bei mir.
USB Stick 32 GB Kingston.
USB Stick 32 GB Kingston.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
General Discussion / Re: Upgrade to -> 22.7 Crowdsec not working.
« on: August 13, 2022, 10:17:48 pm »
AHH i am a idiot 
@mmetc
FYI: My Problem was the Anti DDOS. Syn and Cookies was on.
@mmetc
FYI: My Problem was the Anti DDOS. Syn and Cookies was on.
3
General Discussion / Re: setting up opnsense for the first time
« on: August 13, 2022, 10:15:02 pm »
I like when the dhcp is on opnsense.
But try with your setup. Make a tracert from your clients and then you see where you get
But try with your setup. Make a tracert from your clients and then you see where you get
4
22.7 Legacy Series / Re: pppoe interface does not get created
« on: August 13, 2022, 09:51:36 pm »
Hi
I have made Today with the newest Release a PPOE Con. on 2 Boxes
No Problems at all.
But i must say i have changed the wan Interface for PPOE
BW
I have made Today with the newest Release a PPOE Con. on 2 Boxes
No Problems at all.
But i must say i have changed the wan Interface for PPOE
BW
5
22.7 Legacy Series / Re: Pin Wireguard to a Gateway and/or failover in multi-WAN
« on: August 13, 2022, 09:49:13 pm »
Maybe this can help you ..
https://schnerring.net/blog/opnsense-baseline-guide-with-vpn-guest-and-vlan-support/
https://schnerring.net/blog/opnsense-baseline-guide-with-vpn-guest-and-vlan-support/
6
General Discussion / Re: Help neeged for a problem with Port Forwarding
« on: August 13, 2022, 09:46:09 pm »
Why you have no Pro Support?
7
General Discussion / Re: Upgrade to -> 22.7 Crowdsec not working.
« on: August 06, 2022, 08:15:48 pm »Code: [Select]
level=error msg="auth-api: auth with api key failed return nil response, error: read tcp 127.0.0.1:27107->127.0.0.1:8080: read: connection reset by peer"
8
General Discussion / Re: How to ensure DoT is working correctly?
« on: August 06, 2022, 08:14:44 pm »
yes when you checkd all traffic comes to your opnsense thats my point
https://homenetworkguy.com/how-to/configure-dns-over-tls-unbound-opnsense/
https://homenetworkguy.com/how-to/configure-dns-over-tls-unbound-opnsense/
9
General Discussion / Re: How to ensure DoT is working correctly?
« on: August 06, 2022, 08:00:34 pm »
you said you block all traffic that gets outside that is not encrypted fine.
check it with wireshark. check the unbound logs. monitoring and thats my way i would do it
check it with wireshark. check the unbound logs. monitoring and thats my way i would do it
10
General Discussion / Re: Multi Wan Failover Firewall Configuration
« on: August 06, 2022, 07:46:26 pm »
Have you set monitoring ips for the gateway
When using Unbound for DNS resolution you should also enable Default Gateway Switching via System->Settings->General, as local generated traffic will only use the current default gateway which will not change without this option.
https://docs.opnsense.org/manual/how-tos/multiwan.html
When using Unbound for DNS resolution you should also enable Default Gateway Switching via System->Settings->General, as local generated traffic will only use the current default gateway which will not change without this option.
https://docs.opnsense.org/manual/how-tos/multiwan.html
11
General Discussion / Re: Help neeged for a problem with Port Forwarding
« on: August 06, 2022, 07:31:36 pm »
No Logs on the Firewall from your Client? Tracert? Nslookup? Iptables on the Server?
IProute on the Server?
Wireshark to see if the traffic comes to your firewall or to the server?
IProute on the Server?
Wireshark to see if the traffic comes to your firewall or to the server?
12
General Discussion / Re: setting up opnsense for the first time
« on: August 06, 2022, 07:21:58 pm »
HI
Is the first modem in bridge mode?
When you get a private ip maybe on your wan interface you have to uncheck -> Block private networks (only when you get a private ip dont uncheck when you get a public ip on the wan interface.
Have you made under Service DHCP -> Interface (LAN) -> Enable DHCP with the Range you want?
Is the first modem in bridge mode?
When you get a private ip maybe on your wan interface you have to uncheck -> Block private networks (only when you get a private ip dont uncheck when you get a public ip on the wan interface.
Have you made under Service DHCP -> Interface (LAN) -> Enable DHCP with the Range you want?
13
General Discussion / Re: Route IoT Device with Fixed Source and Dest Address
« on: August 06, 2022, 07:09:25 pm »
Hi
When you create the 2 Networks /Vlans you must have Firewall Rules to allow the traffic between this devices.
The Default is only that when you install opnsense the LAN interface have a allow all and all other networks have a deny all.
Create the Rules start the DHCP and DNS and it will work.
https://homenetworkguy.com/how-to/firewall-rules-cheat-sheet/
https://docs.opnsense.org/manual/firewall.html
When you create the 2 Networks /Vlans you must have Firewall Rules to allow the traffic between this devices.
The Default is only that when you install opnsense the LAN interface have a allow all and all other networks have a deny all.
Create the Rules start the DHCP and DNS and it will work.
https://homenetworkguy.com/how-to/firewall-rules-cheat-sheet/
https://docs.opnsense.org/manual/firewall.html
15
General Discussion / Re: How to ensure DoT is working correctly?
« on: August 06, 2022, 06:31:30 pm »
Maybe you have Clients that have Hardcoded DNS Server i think google chromecast etc.
You can Portforward this clients to opnsense/port.
Why so much dns Upstreams?
You can make a Packet Capture to check if there is any traffic from clients that dont go to your sense.
You can Portforward this clients to opnsense/port.
Why so much dns Upstreams?
You can make a Packet Capture to check if there is any traffic from clients that dont go to your sense.
Pages: [1] 2