1
General Discussion / Re: Setting up - Cannot connect to Internet
« on: April 23, 2022, 10:23:53 pm »
I rebooted my FTTH box and also the protectli and it doesn’t seem to have helped 
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General Discussion / Re: Setting up - Cannot connect to Internet
« on: April 23, 2022, 10:04:02 pm »
Hello,
Thank you - I’ll remove the WAN rules.
I’ve tried pinging from WAN in the diagnostic setting and it fails .
I’ll check the firewall live log again.
Thank you so much
Thank you - I’ll remove the WAN rules.
I’ve tried pinging from WAN in the diagnostic setting and it fails .
I’ll check the firewall live log again.
Thank you so much
3
General Discussion / Setting up - Cannot connect to Internet
« on: April 23, 2022, 09:27:19 pm »
My old set up was an Asus Router and my FTTH would connect directly to the router.
I have a static IP but in the ASUS settings it was just set up as “automatic” and used DHCP. To get the FTTH working I just needed to set the VLAN ID to 10. It didn’t use PPPOE or require authentication. That all worked grand.
I purchased a Protectli 4-port and installed the newest version of OPNsense a few days ago. That all went fine but I’m having a terrible time getting the WAN part to function. LAN is function fine (I can access my plex server no issue)
What I have done:
I went to the VLAN setting and set one up with the tag 10 and assigned it to the WAN parent at igb0
Then I went to assignments and selected WAN and changed it from igb0 to igb0_vlan10.
First I tried setting as static IP and for ipv4 entering in my static IP.
I had went to the firewall rules. Cloned the LAN settings and changed them to WAN so that way everything was pass to test things.
That did not work.
I then changed the WAN settings to DHCP. It would automatically find the static IP and then assigned a gateway. Grand. But still I don’t have access.
I try to ping from the box to anywhere outside and it doesn’t work.
I think I’m missing something obvious but I just can’t figure it out.
I found this person who has a similar situation (except they aren’t static) and tried following what they did:- https://www.geekzone.co.nz/forums.asp?forumid=40&topicid=293308
My settings match and it’s not working for me.
I’ve turned off my OTC and back on several times.
I’m in Ireland and my system is Magnet through NBI.
I’ve spent about nine hours today trying different things and nothing seems to work.
Thank you in advance for your help!
I have a static IP but in the ASUS settings it was just set up as “automatic” and used DHCP. To get the FTTH working I just needed to set the VLAN ID to 10. It didn’t use PPPOE or require authentication. That all worked grand.
I purchased a Protectli 4-port and installed the newest version of OPNsense a few days ago. That all went fine but I’m having a terrible time getting the WAN part to function. LAN is function fine (I can access my plex server no issue)
What I have done:
I went to the VLAN setting and set one up with the tag 10 and assigned it to the WAN parent at igb0
Then I went to assignments and selected WAN and changed it from igb0 to igb0_vlan10.
First I tried setting as static IP and for ipv4 entering in my static IP.
I had went to the firewall rules. Cloned the LAN settings and changed them to WAN so that way everything was pass to test things.
That did not work.
I then changed the WAN settings to DHCP. It would automatically find the static IP and then assigned a gateway. Grand. But still I don’t have access.
I try to ping from the box to anywhere outside and it doesn’t work.
I think I’m missing something obvious but I just can’t figure it out.
I found this person who has a similar situation (except they aren’t static) and tried following what they did:- https://www.geekzone.co.nz/forums.asp?forumid=40&topicid=293308
My settings match and it’s not working for me.
I’ve turned off my OTC and back on several times.
I’m in Ireland and my system is Magnet through NBI.
I’ve spent about nine hours today trying different things and nothing seems to work.
Thank you in advance for your help!
Pages: [1]