Messages

Just adding these in case it makes things more clear. REALLY hoping I didn't waste my money and time waiting for this card to arrive.

Code Select Expand

[2.6.0-RELEASE][admin@pfSense.home.arpa]/root/driver/igb-2.5.19/src: make
make: "/usr/share/mk/bsd.kmod.mk" line 16: Unable to locate the kernel source tree. Set SYSDIR to override.

And output of

Code Select Expand

pciconf -lv

Code Select Expand

none6@pci0:1:0:0: class=0x020000 card=0x0000108e chip=0xabcd108e rev=0x01 hdr=0x00
    vendor     = 'Oracle/SUN'
    device     = 'Multithreaded 10-Gigabit Ethernet Network Controller'
    class      = network
    subclass   = ethernet
none7@pci0:1:0:1: class=0x020000 card=0x0000108e chip=0xabcd108e rev=0x01 hdr=0x00
    vendor     = 'Oracle/SUN'
    device     = 'Multithreaded 10-Gigabit Ethernet Network Controller'
    class      = network
    subclass   = ethernet
none8@pci0:1:0:2: class=0x020000 card=0x0000108e chip=0xabcd108e rev=0x01 hdr=0x00
    vendor     = 'Oracle/SUN'
    device     = 'Multithreaded 10-Gigabit Ethernet Network Controller'
    class      = network
    subclass   = ethernet
none9@pci0:1:0:3: class=0x020000 card=0x0000108e chip=0xabcd108e rev=0x01 hdr=0x00
    vendor     = 'Oracle/SUN'
    device     = 'Multithreaded 10-Gigabit Ethernet Network Controller'
    class      = network
    subclass   = ethernet


Also trying to get the Windows drivers all I can find are .exe's and when  I try running the installer on my VM because it doesn't have the card installed it just gives up and doesn't extract any of the driver files from it....

Seriously. There has to be a way to make those official BSD drivers. But I can't find ANYTHING about how to declare the SYSDIR. I tried editing the Makefile to have SYSDIR=/sys and it still gave me that error.
Legit, if this doesn't work is there a Linux based firewall that is similar? I'm not familiar enough with BSD to screw around with this.

Appreciate the help. Finally getting around to trying at this again. https://www.intel.com/content/www/us/en/support/articles/000005504/ethernet-products/gigabit-ethernet-adapters-up-to-2-5gbe.html

I also still don't understand why I can't just make the BSD drivers.

Code Select Expand

make: "/usr/share/mk/bsd.sysdir.mk" line 15: Unable to locate the kernel source tree. Set SYSDIR to override.


EDIT: Everything I find for this card points me to that page for the drivers, so unless I'm illiterate it should have BSD drivers right? ¯\_(ツ)_/¯

Where's the sys path in opnsense? Can't fiddle with it now since I'm at work. But when I get a chance I'll try it.

Hey. I did google it, and found that page. But that post didn't really help me to get it running. Excuse me for being a noob. But how is it possible to use a windows driver on BSD? And if I have to install the windows drivers on a BSD based OS why are there BSD drivers mentioned in the cards documentation?  Why am I getting this error when I try to make said driver? I'm used to linux where when I run make the most I'll get for an error is a missing dependency. I'm very confused and not really sure where to start. I'm not a complete beginner, but I'm also out of my depth here.

So for all intents and purposes. Please. Treat me like I'm a complete moron and walk me through where to begin, because clearly I've expended the limits of my knowledge.

Hey! I recently picked up an Oracle ATLS21QGE  7055021 NIC to use for my OPNSense router. I know it has BSD support since it's listed in the PDF manual for it. But for the life of me I cannot figure out how to install the drivers for it. Any assistance would be greatly appreciated.

So far I've tried installing the drivers from em-7.7.8.tar.gz that it linked me to, but when I try to run make it just errors saying it can't find my kernal base code.

From what I understand and please correct me if I'm wrong, I need the igb drivers installed but pkg install doesn't know what I'm talking about either. ¯\_(ツ)_/¯ REALLY hoping I didn't waste my money on this NIC.