Messages

May i ask you guys if there is a way to set specific services (from a client) to use a specific WAN?
When the OpenVPN client on OPNsense is enabled, my video on-demand service (amaz....) is not "happy" cause i'm not geo-localizated in the country of subscription.

I can't use the IP based solution (as per my previuos request), cause the TV box should use the VPN to access to content abroad (and use the VPN tunnel as gateway) but only for the video service, should use my in-country WAN.

Thanks  :)

Thanks to both of you!

I'll try and let you know.


EDIT: configuration tested, seems all ok. Thanks again

Hi, many thanks for your help.

I tired this configuration, but not shure if i understood well.

                Protocol   Source                 Port   Destination   Port       Gateway
        IPv4 *   This Firewall           *         *            *       *                                               
        IPv4 *   192.168.1.129/24   *         *            *       WAN_GW_GROUP_NOVPN               
        IPv4 *   LAN net                   *         *            *       WAN_GW_GROUP          

Unfortunatelly, seams it's not working as expected. When this first 2 rules are active all the traffic (included the peer .129)  uses the "NOVPN". If disabled all traffic is routed through VPN.

Any idea? Thanks  :)

Hello,
i'm struggling to find information about this topic.

I would like two different clients on my LAN to use two different gateways.

My configuration, at the moment use 2 WAN in failover configuration (WAN1 fiber and WAN 2 lte). I also have a VPN Client that connect my OPNsense box to a VPN provider (in order to be geolocalized in a specific country).

I set up a gateway group which contain: WAN1+WAN2+VPN and used this gateway with DHCP server.
With this configuration when the VPN is active all the clients within the LAN will use the VPN as gateway, if the VPN is down, i still have the failover option working.

Now the point is that only specific clients, should not use the VPN as gateway but the failover should continue to work. All the clients must be on the same LAN cause they need to "see" each other.

My idea was to have two different gateway group: GW1=WAN1+WAN2+VPN and GW2=WAN1+WAN2, but i don't know how to assign the GW2 only to clients don't the VPN.

Hope the explenation is cleat

Many thanks  :)

Ciao, non sono molto esperto in materia, ma credo che impostando un IP statico sul decoder e andando poi ad aggiungere una ROUTES (System-> Routes -> Configuration) che dice al sistema che quel determinato indirizzo IP(nel tuo caso il decoder) deve uscire direttamente con l'interfaccia fisica WAN, dovresti aver risolto il problema

Same situation, i have 2 ISPs so i can't use the new os-ddclient.

It would be very appreciated if the new version of the plugin had the option "GW_GROUP" among the interface choices

Hi All   :)

I use this post to avoid to open a new one(hope this is not a problem), cause i would like to do the opposite, i'll try to explain.

I have a pci-e  VDSL modem (drytek Vigornic) and i set it as PPPOE WAN connected to my ISP. Since this card has a integrated web page, i need to reach it from the LAN.  WAN interface (re0) has 192.168.1.x/24 class and LAN interface has 192.168.2.x/24 class;  I tried with a bridge rule, but it's not working. 


Thanks

I just received two of them with the non fiber second interface. They come with a half height bracket included in the box. Have not used it yet though. I've been studying the manual ahead of time. I'll test as soon as I build another box.

Hi All, i know this topic is quite old, i'm trying to set a opnsense box with this modem.

Can anyone help?

thanks