Messages

1

22.1 Legacy Series / Re: Virtio just 1gb instead of 10gb

« on: May 18, 2022, 08:03:47 am »

you are right, CPU Speed does matter.
I've tested following:

My Unraid Server (HOST System) runs on an older XEON 4-Core at 3,3Ghz (Xeon® CPU E3-1230 V2)
with following results testing VM-to-Host-Networkspeed via iperf3:
OPNSense only 850mbit/s
Other VMs on the same Host (ubuntu, freebsd13) 18 Gbits/sec

Other VMs on a newer Test-System (Ryzen7-5750G): 25GBits/sec

=> so CPU speed is not the reason for such poor values on OPNSense (hmm.. maybe OPNSense implements some kind of huge overhead, so it's so much slower than other Operating Systems???)

=> passing through PCIe devices is not an option for me, because I use Brigdes on Host for other VMs and Dockers.

2

22.1 Legacy Series / Re: Virtio just 1gb instead of 10gb

« on: May 15, 2022, 12:07:48 am »

I don't need another method to test network speed.

I need a method to improve speed to a level all other VMs (Ubuntu, FreeBSD13) reach "out of the box", and OPNsense does not.

3

22.1 Legacy Series / Virtio just 1gb instead of 10gb

« on: May 14, 2022, 11:31:38 pm »

hello, I run OPNsense as a VM using Unraid as Host.

All Interfaces als virualized using VIRTIO (also tested VIRTIO-NET and E1000).
In Web-UI they are shown as "10Gbase-T <full-duplex>".

When copying files (and testing with iperf3) I only get 1 gbit speed (iperf3 shows 850 Mbits/sec).

Other VMs on the same Host (ubuntu, freebsd13) are running successfully with 10gbit speed (iperf3 shows 18 Gbits/sec).

Settings in OPNsense: CRC, TSO, LRO are deactivated.
Tested on fresh install withoud Shaper.

My Network runs at 10gb and 2.5gbit and 1gbit - and OPNsense is the only limiting element.

Please give some hints what I could try to get full speed.

4

19.7 Legacy Series / Re: VIRTIO NICs not detected anymore

« on: July 29, 2019, 04:45:28 pm »

done - thank you much for "leading" me..

5

19.7 Legacy Series / VIRTIO NICs not detected anymore

« on: July 29, 2019, 04:23:55 pm »

==>> BUG REPORT on 19.7 <<==

I run OPNSense on UNRaid VM (Q35) using virtual NICs (VIRTIO).

On 19.1 only Q35-2.6 worked, using other Q35-x.x there were no NICs detected in OPNsense.
So I ran Q35-2.6, everything fine.

Since update to 19.7 there are no NICs detected anymore!! I tried other Q35 versions, also tried a fresh install an a new VM. => 19.1 shows NICs, 19.7 does not find NICs!!

Now I run a Backup on 19.1 again.

Please HELP.. thanx a lot!!

6

19.7 Legacy Series / Re: OPNSense on KVM (Virtio) ?

« on: July 27, 2019, 05:17:46 am »

I run OPNSense on UNRaid VM (Q35) using 8 virtual NICs (VIRTIO).

On 19.1 only Q35-2.6 worked, otherwise there were no NICs detected in OPNsense.
Since update to 19.7 there are no NICs detected anymore!!

Now I run a Backup on 19.1 again...
HELP?? thanx a lot!!