Messages

Ik heb het werkend hier op glasvezel (KPN via YouFone), wel heb ik een nieuwe WAN interface aangemaakt gekoppeld aan VLAN6. Hierna werkte de verbinding perfect.

Snelheid met OPNsense is vele malen hoger en stabieler dan met het KPN modem.

Item can be closed, has been resolved and working now! :-)
Re-created a rule on my LAN network and it is working now, don't know why it wasn't working before....

Any help would be very very very appreciated  ;D ::)

I really don't know where to look or where it is going wrong? Only thing different than on the remote side is that we have 2 ISP's for failover. Buth I cannot disable that because of a production enverionment this is working on.

I hope some genius can help me in the right direction :-)

I don't know how to use TCPDUMP (sorry!), tried to trace from my machine and it goes to my OPNsense and then nothing.

Tracing route to 192.168.5.254 over a maximum of 30 hops

  1    <1 ms    <1 ms    <1 ms  OPNsense.maedilon.local [192.168.1.254]
  2     *        *        *     Request timed out.

When I do a traceroute from console I get this:
traceroute to 192.168.5.254 (192.168.5.254), 64 hops max, 40 byte packets
1  powered-by.xenosite.net (89.255.45.241)  0.574 ms  0.327 ms  0.324 ms
2  * * *

89.255.45.241 is the gateway of my default WAN.

When I trace from the remote site I get this response:
Tracing route to 192.168.1.254 over a maximum of 30 hops

  1    <1 ms    <1 ms    <1 ms  192.168.5.254
  2     4 ms     5 ms     4 ms  192.168.1.254

Trace complete.

When I take a look at the route in the OPNsense it looks good:

Local side:
ipv4 192.168.5.0/24 89.255.45.241 US 800 1500 igb1 XenositeWAN

Remote side:
ipv4 192.168.1.0/24 139.156.151.64 US 0 1492 pppoe0 WAN_KPN

In the attachment you will find 3 printscreens:
- Local site - LAN
- Remote site - LAN
- Remote site - VPN Status

Local LAN: 192.168.1.0/24
Remote LAN: 192.168.5.0/24

I added the rule on the local LAN to allow network to remote subnet through the primary gateway buth no luck.

Hello,

I have 2 OPNsense firewalls with versions:
OPNsense 19.7.5_5-amd64
FreeBSD 11.2-RELEASE-p14-HBSD
OpenSSL 1.0.2t 10 Sep 2019

On both firewalls I have set up a IPsec VPN tunnel, tunnel is connected and all working fine buth traffic is routing/passing only from 1 side.

There is one difference in setup, one location has 2 WAN connections (failover group) and the other has only one WAN connection.

Local site: multiple WAN
Remote site: single WAN

Data from remote to local is goin fine, buth data from local to remote site is not working.
I think the issue is because we have a multi WAN setup on our site.

I already tried to push the data to the remote subnet from our LAN to the default gateway the VPN is connected on buth no luck.

Any help / advise in this one would be great! :-)

Dear,

Our provider (KPN) is changing from PPPoE to IPoE for the WAN connection.
In the WAN interface I have no option to enable or setup this type of WAN connection.

Do you now how I need to setup my new WAN connection?
Thanks! :-)