Messages

1

22.7 Legacy Series / Re: netgate 6100 / igcX no link..

« on: October 31, 2022, 02:05:39 pm »

Any luck?

I have a Netgate 6100 as well and was thinking of giving OPNsense another try. It's been years since I last used it.

2

18.7 Legacy Series / Re: OPNsense won't reboot (CAM status: Command timeout)

« on: November 03, 2018, 06:25:15 pm »

My wife will kill me if I take down the Wi-Fi one more time this week We had a lot of downtime hahaha.

I will give it a shot next week and report back.

3

18.7 Legacy Series / Re: OPNsense won't reboot (CAM status: Command timeout)

« on: November 03, 2018, 06:13:57 pm »

No it's a good question I only installed pfSense 2.4.4.

It might be a hardware compatibility issue with the FreeBSD version that comes with OPNsense. Just a wild guess.

4

18.7 Legacy Series / Re: OPNsense won't reboot (CAM status: Command timeout)

« on: November 03, 2018, 01:46:13 pm »

I gave up. Back to pfSense.

5

18.7 Legacy Series / OPNsense won't reboot (CAM status: Command timeout)

« on: October 31, 2018, 06:32:03 pm »

I (finally) managed to install OPNsense on my Qotom box but sadly encounter a new issue.

Completing the wizard after installing to the local hard disk drive (SSD) is not an issue. Things went south as soon as I rebooted the machine.

The errors I'm getting: https://tweakers.net/ext/f/61Nb85twZgIWqcRgavtBoAI7/full.jpg

Basically

ahcich0: Timeout on slot 24 port 0
WRITE_FPDMA_QUEUED
CAM status: Command timeout
Retrying command

And this keeps on going getting nowhere.

I do not have this issue with Debian or pfSense.

Anyone a clue maybe?

6

18.7 Legacy Series / Re: Mounting failed with error 19 during installation

« on: October 31, 2018, 06:21:21 pm »

Managed to resolve this after two very frustrating nights. I think it was an issue related to an old MBR or broken GPT configuration.

Steps to resolve:

1. Connect an USB flash drive (to my Mac)
2. diskutil list (check who's who)
3. diskutil umount disk2s1 (unmount the flash drive - in my case disk2s1)
4. gzcat pfSense-CE-memstick-2.4.4-RELEASE-amd64.img.gz | sudo dd of=/dev/rdisk2 bs=1m (deploy the image)
5. Install pfSense on the Qotom box using the USB flash drive

Success. The hard disk drive is now OK and ready for OPNsense. Continuing:

6. Connect the USB drive to the Mac once again
7. diskutil list
8. diskutil umount disk2s1
9. sudo dd bs=1m if=OPNsense-18.7-OpenSSL-vga-amd64.img of=/dev/rdisk2

Et voilà.. I am now installing OPNsense!

7

18.7 Legacy Series / Mounting failed with error 19 during installation

« on: October 30, 2018, 09:12:44 pm »

I'm trying to install OPNsense (for the first time) on my Qotom box using USB. But no luck. This is the error I'm getting during the initial startup:

mountroot: waiting for device /dev/ufs/OPNsense_Install...
Mounting from ufs:/dev/ufs/OPNsense_Install failed with error 19.

etc. etc.

Picture of the output on my display: https://tweakers.net/ext/f/Q9fh5nRGpbz0naAnO4ZJM3Zg/full.jpg

Anything I can do to resolve this issue?