Messages

Thanks cookiemonster! that's exactly what I expected it to do, but I get the error above.
Franco, I only have one disk. I tried the ZFS choice, and it did in, fact, work. I think I misspoke in my OP, My old brain didn't remember everything correctly. Since my current system is UFS I guess only tried that. I did try UFS again after the ZFS, and got the same error.
The ZFS clone booted up fine in a disconnected test environment.
Thanks everyone for your help and time.

I have not, but that has nothing to do with my question. That statement is in the documentation. How do I use it?

In the OPNsense documentation here: https://docs.opnsense.org/manual/install.html#opnsense-installer is the statement:

The installer can always be run to clone an existing system, even for Nano images. This can be useful for creating live backups for later recovery.

I have tried to do this unsuccessfully several times. I use the UFS GPT/UEFI Hybrid install and also tried the ZFS install. It always ends with the error:

Error mounting partition /mnt: mount: /dev/gpt/rootfs: Device busy

Is there any other documentation about how to do this? Live backups for later recovery sounds like an excellent idea!

thx

What happens if you enable Unbound instead ?

No luck with Unbound either.

If your setup is simple enough, it might be worth just noting your settings and starting with a fresh install of 23.7.

Not sure what your use case is that made you use dnsmasq instead of unbound but the default setup works well.

I was wondering about a fresh install. Can I back up my config, and restore it to a fresh install?

Unbound seems overly complicated and I've used Dnsmasq before. I just need a simple lookup for my internal hosts and pass everything else out to the Internet. My external DNS is hosted on Azure.

Nope. I have a static IP from my Internet provider and it is assigned to the WAN.
I haven't made any config changes. It was working before the update.

More info:
From the console, I cannot ping any IP address on the Internet, even though I can from clients on the LAN.
From the console I CAN ping LAN IP addresses.
From the console I get communications failed with ALL listed DNS servers, internal and external.

I have neglected updating OPNsense for too long, apparently. I was on 22.7. I checked for updates and was presented with the upgrade to 23.1_6. I have never had problems with OPNsense updates in the past, and figured I would need to do a couple to get up to date. I clicked the update button. All seemed to go well and the system came back up.
The problem I am having now is the LAN interface is not responding to DNS queries on port 53. From clients on the LAN,  I can ping internal and external hosts by IP address, but not host name. All the clients have the correct network info from DHCP.  An NMAP scan from a Linux client shows port 53 closed.  I have restarted the OPNsense server a few times, and I have not made any changes, yet.
I also cannot upgrade further via the GUI because of the problem. Check for updates just times out.
I am using Dnsmasq as DNS service.
I do not use any ad blocking service (i.e. Adguard, Pihole, etc).

Any advice on next steps would be appreciated.

This guide worked perfectly for me:

https://www.bitblock.com/blog/security/69-fixing-nat-for-a-nintendo-switch-using-upnp-w-custom-configuration

buzz

Hi, This is my first OPNSense install. I have a motherboard with an on board Intel mini PCIe wifi card. It is not showing up in the web interface.
I ran the following commands and I don't see the driver loaded, but I do see it in the PCI bus dump, at the very bottom:

Code Select Expand

root@shou:~ # sysctl -n net.wlan.devices

root@shou:~ # pciconf -vl
hostb0@pci0:0:0:0:      class=0x060000 card=0x14221022 chip=0x14221022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Root Complex'
    class      = bridge
    subclass   = HOST-PCI
vgapci0@pci0:0:1:0:     class=0x030000 card=0x01231002 chip=0x13131002 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD/ATI]'
    device     = 'Kaveri [Radeon R7 Graphics]'
    class      = display
    subclass   = VGA
hdac0@pci0:0:1:1:       class=0x040300 card=0x01231002 chip=0x13081002 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD/ATI]'
    device     = 'Kaveri HDMI/DP Audio Controller'
    class      = multimedia
    subclass   = HDA
hostb1@pci0:0:2:0:      class=0x060000 card=0x00000000 chip=0x14241022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    class      = bridge
    subclass   = HOST-PCI
pcib1@pci0:0:2:1:       class=0x060400 card=0x12341022 chip=0x14251022 rev=0x00 hdr=0x01
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    class      = bridge
    subclass   = PCI-PCI
hostb2@pci0:0:3:0:      class=0x060000 card=0x00000000 chip=0x14241022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    class      = bridge
    subclass   = HOST-PCI
pcib5@pci0:0:3:1:       class=0x060400 card=0x12341022 chip=0x14261022 rev=0x00 hdr=0x01
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Root Port'
    class      = bridge
    subclass   = PCI-PCI
hostb3@pci0:0:4:0:      class=0x060000 card=0x00000000 chip=0x14241022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    class      = bridge
    subclass   = HOST-PCI
xhci0@pci0:0:16:0:      class=0x0c0330 card=0x50041458 chip=0x78141022 rev=0x09 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB XHCI Controller'
    class      = serial bus
    subclass   = USB
xhci1@pci0:0:16:1:      class=0x0c0330 card=0x50041458 chip=0x78141022 rev=0x09 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB XHCI Controller'
    class      = serial bus
    subclass   = USB
ahci0@pci0:0:17:0:      class=0x01018f card=0xb0021458 chip=0x78001022 rev=0x40 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH SATA Controller [IDE mode]'
    class      = mass storage
    subclass   = ATA
ohci0@pci0:0:18:0:      class=0x0c0310 card=0x50041458 chip=0x78071022 rev=0x11 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB OHCI Controller'
    class      = serial bus
    subclass   = USB
ehci0@pci0:0:18:2:      class=0x0c0320 card=0x50041458 chip=0x78081022 rev=0x11 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB EHCI Controller'
    class      = serial bus
    subclass   = USB
ohci1@pci0:0:19:0:      class=0x0c0310 card=0x50041458 chip=0x78071022 rev=0x11 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB OHCI Controller'
    class      = serial bus
    subclass   = USB
ehci1@pci0:0:19:2:      class=0x0c0320 card=0x50041458 chip=0x78081022 rev=0x11 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB EHCI Controller'
    class      = serial bus
    subclass   = USB
none0@pci0:0:20:0:      class=0x0c0500 card=0x780b1022 chip=0x780b1022 rev=0x16 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH SMBus Controller'
    class      = serial bus
    subclass   = SMBus
atapci0@pci0:0:20:1:    class=0x01018a card=0x50021458 chip=0x780c1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH IDE Controller'
    class      = mass storage
    subclass   = ATA
hdac1@pci0:0:20:2:      class=0x040300 card=0xa0021458 chip=0x780d1022 rev=0x01 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH Azalia Controller'
    class      = multimedia
    subclass   = HDA
isab0@pci0:0:20:3:      class=0x060100 card=0x780e1022 chip=0x780e1022 rev=0x11 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH LPC Bridge'
    class      = bridge
    subclass   = PCI-ISA
pcib6@pci0:0:20:4:      class=0x060401 card=0x00000000 chip=0x780f1022 rev=0x40 hdr=0x01
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH PCI Bridge'
    class      = bridge
    subclass   = PCI-PCI
ohci2@pci0:0:20:5:      class=0x0c0310 card=0x50041458 chip=0x78091022 rev=0x11 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'FCH USB OHCI Controller'
    class      = serial bus
    subclass   = USB
pcib7@pci0:0:21:0:      class=0x060400 card=0x00001022 chip=0x43a01022 rev=0x00 hdr=0x01
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Hudson PCI to PCI bridge (PCIE port 0)'
    class      = bridge
    subclass   = PCI-PCI
hostb4@pci0:0:24:0:     class=0x060000 card=0x00000000 chip=0x141a1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Function 0'
    class      = bridge
    subclass   = HOST-PCI
hostb5@pci0:0:24:1:     class=0x060000 card=0x00000000 chip=0x141b1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Function 1'
    class      = bridge
    subclass   = HOST-PCI
hostb6@pci0:0:24:2:     class=0x060000 card=0x00000000 chip=0x141c1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Function 2'
    class      = bridge
    subclass   = HOST-PCI
hostb7@pci0:0:24:3:     class=0x060000 card=0x00000000 chip=0x141d1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Function 3'
    class      = bridge
    subclass   = HOST-PCI
hostb8@pci0:0:24:4:     class=0x060000 card=0x00000000 chip=0x141e1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Function 4'
    class      = bridge
    subclass   = HOST-PCI
hostb9@pci0:0:24:5:     class=0x060000 card=0x00000000 chip=0x141f1022 rev=0x00 hdr=0x00
    vendor     = 'Advanced Micro Devices, Inc. [AMD]'
    device     = 'Family 15h (Models 30h-3fh) Processor Function 5'
    class      = bridge
    subclass   = HOST-PCI
pcib2@pci0:1:0:0:       class=0x060400 card=0x00000000 chip=0x8018111d rev=0x0e hdr=0x01
    vendor     = 'Integrated Device Technology, Inc. [IDT]'
    device     = 'PES12N3A PCI Express Switch'
    class      = bridge
    subclass   = PCI-PCI
pcib3@pci0:2:2:0:       class=0x060400 card=0x00000000 chip=0x8018111d rev=0x0e hdr=0x01
    vendor     = 'Integrated Device Technology, Inc. [IDT]'
    device     = 'PES12N3A PCI Express Switch'
    class      = bridge
    subclass   = PCI-PCI
pcib4@pci0:2:4:0:       class=0x060400 card=0x00000000 chip=0x8018111d rev=0x0e hdr=0x01
    vendor     = 'Integrated Device Technology, Inc. [IDT]'
    device     = 'PES12N3A PCI Express Switch'
    class      = bridge
    subclass   = PCI-PCI
em0@pci0:3:0:0: class=0x020000 card=0x11bc8086 chip=0x10bc8086 rev=0x06 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82571EB Gigabit Ethernet Controller (Copper)'
    class      = network
    subclass   = ethernet
em1@pci0:3:0:1: class=0x020000 card=0x11bc8086 chip=0x10bc8086 rev=0x06 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82571EB Gigabit Ethernet Controller (Copper)'
    class      = network
    subclass   = ethernet
em2@pci0:4:0:0: class=0x020000 card=0x11bc8086 chip=0x10bc8086 rev=0x06 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82571EB Gigabit Ethernet Controller (Copper)'
    class      = network
    subclass   = ethernet
em3@pci0:4:0:1: class=0x020000 card=0x11bc8086 chip=0x10bc8086 rev=0x06 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82571EB Gigabit Ethernet Controller (Copper)'
    class      = network
    subclass   = ethernet
re0@pci0:5:0:0: class=0x020000 card=0xe0001458 chip=0x816810ec rev=0x06 hdr=0x00
    vendor     = 'Realtek Semiconductor Co., Ltd.'
    device     = 'RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller'
    class      = network
    subclass   = ethernet
none1@pci0:7:0:0:       class=0x028000 card=0x40708086 chip=0x08b18086 rev=0xbb hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Wireless 7260'
    class      = network
 

How do I get the drivers loaded for it?

Thanks for the help! I'm loving OPNSense so far!

buzz