Messages

1

General Discussion / Re: OPNsense nano on APU2 with SD card

« on: June 08, 2018, 10:29:21 pm »

ok but I thought it was meant to be put on the SD card directly without further steps.

I guess we can close this.

Thank you

2

General Discussion / Re: OPNsense nano on APU2 with SD card

« on: June 01, 2018, 10:01:41 pm »

But the idea of the nano image is not to write it directly on the SD card?

Then insert the SD in the APU and install from it?

It's doing the same thing on a USB flash drive.
- write the nano image on the USB drive
- boot on it (there is no other boot device available)
- when it's ready, I reboot
- same probleme

3

General Discussion / Re: OPNsense nano on APU2 with SD card

« on: June 01, 2018, 05:21:37 pm »

Hi Franco,

I did not had any come back yet to ship the unit.

Until then, can you tell me how you install it with the nano image?

4

General Discussion / Re: OPNsense nano on APU2 with SD card

« on: May 28, 2018, 02:46:27 pm »

Hi,

Sorry for the delay I just came back from vacation today.

I asked my boss about sending one to you. Can you PM the address?

I'll get back to you as soon as he will tell me if I can send it or not.

5

General Discussion / Re: OPNsense nano on APU2 with SD card

« on: May 18, 2018, 06:02:54 pm »

What do you mean by "share"? Like sending one kit over? Or you only need the model numbers?

The board is APU2C2
https://www.pcengines.ch/apu2c2.htm

SD cards are Kingston SDA10/16GBCR and SDCS/16GBCR
https://www.kingston.com/en/flash/sd_cards/sda10
https://www.kingston.com/en/flash/microsd_cards/sdcs

6

Development and Code Review / Re: Feature request - Reset all states if WAN IP Address changes

« on: May 18, 2018, 05:47:51 pm »

Ok I'll do.

Thank you

7

Development and Code Review / Feature request - Reset all states if WAN IP Address changes

« on: May 16, 2018, 04:51:26 pm »

Hi,

Can't find this feature on OPNsense. I need this to pull the plug on pfSense...

On pfSense:

Reset All States
Reset all states if WAN IP Address changes
This option resets all states when a WAN IP Address changes instead of only states associated with the previous IP Address.

Thank you!

8

General Discussion / Re: OPNsense nano on APU2 with SD card

« on: May 16, 2018, 04:00:06 pm »

Hi Franco,

I tried at least 3 different models of SD card. I had the same problem with pfSense.

The exact board model is APU2C2.

It does work great with USB installer but it takes a bit more time to setup. We install a lot of these.

9

General Discussion / OPNsense nano on APU2 with SD card

« on: May 14, 2018, 03:56:21 pm »

Hi everyone,

I can't find the answer so I'm posting my question here.

The problem I have is OPNsense won't reboot. The installation go through but at reboot it says "Can't load Kernel".

I had the same problem with previous version 17. Tried i386 and amd64. BIOS on APU2 is up to date (4.6.8 ). Connected with PuTTY at speed 115200.

What I did:
- Write the SD card with the current nano image (18.1.6) with Win32DiskImager.
- Put the SD card in the APU2.
- Power it on. Everything's going fine.
- When the menu appears I hit the reboot option.
- After couples of minutes it says "Can't load Kernel".

Also, when it's booting, all the characters are dduupplliiccaatteedd.

Any idea?

Thank you.