Messages

Hi

Has anybody experienced problems with openvpn client setups after the 16.7.8 update?
My client vpn's are not working anymore.
The log showes they(3 seperate vpn)connect but after some seconds the log shows different failures.
When disabling 2 of the clients i get the active client to reconnect, but it failes again after some seconds.
The log almost always shows these 3 lines or line 1 and 3
MANAGEMENT:Client disconnected
MANAGEMENT:CMD 'status 2'
MANAGEMENT:CMD 'state 1'
after that it reconnects again

Does anybody has an idea whats wrong?

Hi Franco, thanks for the reply.

I tried the to boot from are USB stick, but my system has the USB error 19 behavior.
I did a new install with a SATA CD-rom connected, that worked.

Wright now I have my backup opnsense box running, so i will try the update once more tomorrow.

Regards
Sebastian

Hi

Has anybody encountered the same problem.
I just update my working opnsense box from 16.7.1 LibreSSL to 16.7.2 OpenSSL and it broke the UEFI boot.
Now when in the boot there is the message:
Failed to load '/boot/loader.efi'
Panic: No bootable partition found!

Any ideas?

Hi Franco

Thank you for the reply.

It's an cdrom/VGA install on a 1,5 year old firewall motherboard.
The motherboard is mounted in an older server chassis with dual power supply and the whole System(firewall, switch, AP...) is on an 6KW Eaton UPS.
The same setup has run the week before the upgrade for 48 days without a hiccup, but I will try another power supply.
As I wrode in the firt post this happens most often when the system is "idle", could it be a power state or memory issue?

PS:The only difference from the previous install is that the SSD is now GPT not MBR.

Regards
Sebastian

Hi all

After the upgrade from 16.1 to 16.7  didnt work very well(openvpn clients didnt work, gateways shown up twice) i decided to reinstall 16.7 last weekend.
After fiddeling around for a while with the USB-pen installer issue i got it installed and after a komplete new configuration everything was working perfect.

Now on monday things got strange.
After running for some time, the opnsense box rebooted on it's own when i was at work.
After coming home i checked opnsense and during my checks i rebooted again 4 times in 20/25min.
Then i stresstested it with setting up a couple of downloads with about 65-75 Mbps troughput over VPN.the firewall ran without a hickup.
Today it started again with the random reboots.

Can anybody tell me where to find the complete log?
The logfile under System-»Log file only shows logs after the last reboot

Regards
Sebastian

Hi all

I use opnsense in a multi-VPN-WAN loadbalancing/failover setup.
The setup is from my vpn provider forum for setting up a multi wan vpn firewall, all traffic routed through one of the vpn wan's.
Today i tried traceroute and the result is showing my ISP ip address.
I tested my setup with 3-4 DNS leak test sites and all are reporting no DNS leaks.
Since i'am not a firewall expert, my question is:
Is this an expected result?

Thanks in advance :-)

Hi everybody

I have been using Opnsense for over a year now and it's really a great product.

I use it to root all my traffic over a multi(3) vpn wan loadbalancing/failover config.
To set it up i followed a how-to in the vpn provider forum.

Since i'am not an firewall expert i have more and more questions about the rulesets i use and if there is a better way to set it up.
One example is the opnense.org how-to that explains how to set up Spamhaus.When setting up the firewall rules i wonder if i should choose my loadbalancing/failover group or both under the "gateway"?

I wonder if there is anybody that can help with this or is it possible to pay for such support?

Regards
Seb

Hi

Thanks for the reply
Sorry, i didn't mention that i have seen this massage after a normal reboot from within Opnsense.
I'am definitive no expert on BSD/Unix, so i think there is nothing i can help with.

I will try to remenber to follow the boot sequence when the next reboot happens.
I report back when i see somthing different.

Regards
Sebastian

[Trying to mount root from ufs:/dev/ada0s1a [rw]...WARNING: /mnt was not properly dismountedMounting filesystems...tunefs: soft updates remains unchanged as enabledtunefs: file system reloadedWARNING: /mnt was not properly dismounted]

Hi

i'am, seeing this warning Message when i look at the boot cycle via the serial console.
I have seen this mesage before, but there has never been an issue, so i have overlooked it.
Trying to mount root from ufs:/dev/ada0s1a [rw]...
WARNING: /mnt was not properly dismounted
Mounting filesystems...
tunefs: soft updates remains unchanged as enabled
tunefs: file system reloaded
WARNING: /mnt was not properly dismounted

Is this something to worry about?

Regards
Seb

Thank you very much for the fast response and fix for this problem.

I'am very immpressed With Opnsense, keep up the excellent work.

Hei

I' am running a Opnsense Box With3 VPN WAN Connections in a loadbalancing/failover config.
After updating to 16.1.4 the services status view shows all the OpenVPN Client services as not started, dwspite all of them runing.
The same issue is in VPN->Connection Status

Does somebody have the same problem or has any tip for an solution?

Seb