"
Just updated from 25.1.11 and everything seems good. I use CrowdSec,Dnsmasq,os-chrony,os-cpu-microcode-intel,os-nut,os-udpbroadcastrelay and os-wol . I did notice ISC DHCPv4 was configured on 25.1.11, but nothing is in the GUI now. I,m not using ISC DHCPv4,but did want to mention it. I will see if anything comes up.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
23.1 Legacy Series / Wireguard
January 15, 2023, 08:26:48 AM
I'm using Wireguard. I install the os-wireguard plugin and then "pkg install wireguard-kmod".
To test 23.1 would I "# opnsense-update -ur 23.1.r1" then remove the plug-in or remove it from 22.7.10_2 before the update.
To test 23.1 would I "# opnsense-update -ur 23.1.r1" then remove the plug-in or remove it from 22.7.10_2 before the update.
#3
22.1 Legacy Series / Monit with Surfshark
June 25, 2022, 05:53:18 PM
Hello.
It's probably me over thinking this or just being a little daft.
I want to restart my openVPN (Surfshark) connection when it goes down.
It never has the same ip. I have searched the forum and found some information, but find myself really confused right now.
Is their not a simple straight forward way of implementing this.
I'm running OPNsense 22.1.9-amd64.
It's probably me over thinking this or just being a little daft.
I want to restart my openVPN (Surfshark) connection when it goes down.
It never has the same ip. I have searched the forum and found some information, but find myself really confused right now.
Is their not a simple straight forward way of implementing this.
I'm running OPNsense 22.1.9-amd64.
#4
21.7 Legacy Series / Everything Seen to Work
July 09, 2021, 06:12:23 PM
Just installed 21.7R1 on a VM in Proxmox 7.0. I have a Intel I350 T2 bypassed through to a vm. i have Surfshark VPN on a vlan. I imported my config at install to a zfs install. I also have a lan bridge through proxmox.
Everything seems to work fine.
Don't know if you want to hear of successful installs here, but wanted to post of my experience.
Thank you for all your work on this.
Everything seems to work fine.
Don't know if you want to hear of successful installs here, but wanted to post of my experience.
Thank you for all your work on this.
#5
21.1 Legacy Series / Migrated from pfSense to OPNsense
March 08, 2021, 04:30:25 PM
Hello!
I have a couple of questions if someone can help.
I am coming from pfSense and had it setup using this https://nguvu.org/pfsense/pfsense-baseline-setup/.
I use OPNsense in a Proxmox VM and all three network cards are pass-through (one is an onboard Intel). Same as i did with pfSense.
Proxmox has the a dual port i350 network card for itself and vlans, 5 network interfaces in total.
I see in OPNsense the floating rules have a Default reject. Do I need to add a Default reject IPv4 at the end of my individual vlan rules?
I'm a little confused on how Floating rules are applied. Individual rules make sense being from top down.
In the baseline setup he uses localhost in the DNS Forwarder setup. It's not in the OPNsense GUI. How would I configure OPNsense to mirror my old setup?
I have everything set through unbound at the moment and have switched to SurfsharkVPN.
Everything seems to be working.
My final problem is I don't get internet in my Container's in Proxmox. All other VM's do get normal network. If I setup a new VM dhcp works ,but, not in a Container, It all worked in my old setup.
Sorry if these have been answered somewhere before, I looked but did not find anything.
An old retired millwrght very much appreciate any help.
Brian
I have a couple of questions if someone can help.
I am coming from pfSense and had it setup using this https://nguvu.org/pfsense/pfsense-baseline-setup/.
I use OPNsense in a Proxmox VM and all three network cards are pass-through (one is an onboard Intel). Same as i did with pfSense.
Proxmox has the a dual port i350 network card for itself and vlans, 5 network interfaces in total.
I see in OPNsense the floating rules have a Default reject. Do I need to add a Default reject IPv4 at the end of my individual vlan rules?
I'm a little confused on how Floating rules are applied. Individual rules make sense being from top down.
In the baseline setup he uses localhost in the DNS Forwarder setup. It's not in the OPNsense GUI. How would I configure OPNsense to mirror my old setup?
I have everything set through unbound at the moment and have switched to SurfsharkVPN.
Everything seems to be working.
My final problem is I don't get internet in my Container's in Proxmox. All other VM's do get normal network. If I setup a new VM dhcp works ,but, not in a Container, It all worked in my old setup.
Sorry if these have been answered somewhere before, I looked but did not find anything.
An old retired millwrght very much appreciate any help.
Brian
#6
18.1 Legacy Series / ASRock J4205-ITX and J3455-ITX / Intel Apollo Lake not booting.
January 12, 2018, 04:15:19 PM
I have a Asrock J3555B-ITX board and have to add hint.hpet.0.clock="0" to /Boot/loader.conf.local in pfsense.
I want to use Opnsense for my Airvpn and replace pfsense 2.4.2.
Is their and patches or other work around for Opnsense 18.1.
Apparently their is a kernel patch for this.
Two post, first a work around from here https://forum.pfsense.org/index.php?topic=138221.15
and some kernel used here https://forums.freebsd.org/threads/59653/.
Sorry if this is in the wrong place.
I want to use Opnsense for my Airvpn and replace pfsense 2.4.2.
Is their and patches or other work around for Opnsense 18.1.
Apparently their is a kernel patch for this.
Two post, first a work around from here https://forum.pfsense.org/index.php?topic=138221.15
and some kernel used here https://forums.freebsd.org/threads/59653/.
Sorry if this is in the wrong place.
Pages1
