Advice needed: Mini PC for my first OPNsense firewall

Started by sam1970, November 16, 2026, 08:18:21 PM

Previous topic - Next topic
Advice needed: Mini PC for my first OPNsense firewall

Hi everyone,

I'm new to OPNsense and would like to set up a dedicated mini PC as a firewall for my home network and homelab, running OPNsense directly on the hardware without Proxmox.

My current setup consists of an ISP modem/router, two managed Netgear switches (GS108E and GS308Ev4), a QNAP TS-664 running Docker containers (Pi-hole, Unbound, WireGuard), and a Raspberry Pi 5 running a second Pi-hole. I also use Proton VPN for selected traffic.

I'd like to gradually move routing, NAT, DHCP, VLANs and VPN management to OPNsense. I'm also interested in experimenting with Suricata IDS/IPS, Zenarmor and network monitoring. Gigabit speeds are sufficient for my needs, and since I already have managed switches, two physical network ports are enough.

Hardware

After browsing this forum, I came across the **HUNSN RJ35 with Intel Core i3-N305 (DDR4 version)**:

Amazon

I'd prefer a slightly more powerful CPU than strictly necessary to leave some headroom for future use.

I already have the following components available:

- 8 GB Transcend DDR4-2666 SO-DIMM (TS1GSH64V6B).
- 2× WD Red SN700, 250 GB NVMe M.2 2280.

According to the specifications, the HUNSN supports DDR4-3200. I'd like to start with my existing DDR4-2666 module and possibly upgrade to 16 GB DDR4-3200 later, when RAM prices become more reasonable. One NVMe drive is sufficient for my needs.

My questions

1. Does anyone have experience with this HUNSN N305? How reliable is it for 24/7 operation, particularly regarding cooling, power consumption, BIOS support and potential Intel i226-V issues?
2. Will my DDR4-2666 module work in this DDR4-3200 system, and is 8 GB enough to get started with Suricata?
3. Based on your own experience, are there any better mini PCs you would recommend?
4. Which OPNsense plugins or features would you recommend for a homelab? I'm considering Suricata, Zenarmor, ntopng, WireGuard and policy-based routing through Proton VPN.
5. Would you recommend keeping my existing Pi-hole installations, or would Unbound with DNS filtering in OPNsense be a good alternative? I'm also considering NetAlertX as a replacement for Fing for network device discovery.

My main priorities are reliable 24/7 operation, good firmware support and reasonable power consumption. I'm specifically looking for a compact mini PC, not a rackmount server.

Thanks in advance for your advice and experiences!

AFAIK, the HUNSN RJ35 was available as DDR-5 model only. The link you gave lead me to a different brand machine with DDR-4, but beware: that one has only 2 Realtek Gbit ports, so no 2.5 Gbit and non-Intel. That, I would avoid.

You will get no "decent" firmware support with any of these chinese machines, if any at all. That mostly does not matter much, because all that matters will be CPU microcode updates, which are included in OpnSense anyway. The only thing that matters id stability and potentially, power draw.

I would go for a 4 port I226V specimen and upgrade both RAM and SSD myself, so you can go for good brand units.
Intel N100, 4* I226-V, 2* 82559, 16 GByte, 500 GByte NVME, Leox LXT-010H-D

1100 down / 450 up, Bufferbloat A+

November 16, 2026, 09:57:23 PM #2 Last Edit: November 16, 2026, 09:59:35 PM by sam1970
Thanks for your advice. You're right about the Amazon listing. It's surprisingly difficult to find a reliable, reasonably priced mini PC for OPNsense on Amazon.

I've also been looking at Protectli and found these two models:

- VP3230: Intel N305, 8 cores, 2× Intel i226-V, DDR5 — €482.79 incl. VAT.
- VP2430e: Intel N150, 4 cores, 4× Intel i226-V, DDR5 — €458.59 incl. VAT.

Both are fanless and support NVMe storage.

I'm leaning towards the VP3230. For just €24.20 more, it offers twice the CPU cores and more headroom for experimenting with Suricata and other features.

Since I already use managed switches, I assume two Ethernet ports (WAN and LAN with VLANs) should be sufficient.

You recommended a four-port i226-V system, but I haven't been able to find a suitable four-port N305 model that's readily available to buy.

Is there a particular advantage to having four physical ports in my setup when everything is connected through managed switches?

Which of these two Protectli models would you choose, or would you recommend something else in this price range?

Thanks again!


November 16, 2026, 10:08:23 PM #3 Last Edit: November 16, 2026, 10:28:42 PM by meyergru
Yes, there are two advantages:

1. When you use cross-VLAN-traffic, you do not share the bandwidth of one port. That might come in handy when you use file transfers from a NAS to a PC when both are connected via 2.5 Gbps. Incidentally, 300 MByte/s seems to be the speed where RAID-volumes with HDDs max out and also, Nxxx CPUs can also do that.

2. FreeBSD (and hence OpnSense) does not like mixing tagged VLANs and untagged traffic on the same interface. While you can fix that by using all tagged VLANs, some vendors prefer their management VLAN untagged (e.g. Unifi). Thus, you need two LAN interfaces: one untagged and the other for all tagged VLAN traffic.

That is obviously impossible with only two ports, unless you use another VLAN for WAN traffic. In that case, you can also use a router-on-a-stick.

Another warning: Cheap china boxes are often worse in cooling performance than, say, brand variants like Protectli (they also offer firmware updates). N305 uses more power than N150, despite having the same max TDP. (almost no vendor actually limits those units at their base TDP) While it is true that the performance is slightly better, it all originates from more threads. Last time I looked, Zenarmor supported only single threading in the CE version.

Supply of these boxes has diminished severely since prices are so high. You could get yourself an N1x0 four port box without RAM and SSD for < 200€ in 2025. The same box now costs >300€ and the RAM and NVME come in at another 200 instead of 100€.
Intel N100, 4* I226-V, 2* 82559, 16 GByte, 500 GByte NVME, Leox LXT-010H-D

1100 down / 450 up, Bufferbloat A+

Four network interfaces vrs two is to not constraint yourself from the start if you can avoid it. Yes you need only two but you'll soon find use for the spare ones.
Memory DDR4-3200 vrs DDR4-2666 makes very little difference in a router firewall IMHO. Use what you have. You'll need to research a little what works on them.
Since you say you are new to this, I'd suggest getting the basics going first before moving on. That is get your core services going: routing, firwalling, NAT, DHCP. Once you put it in place disable your existing ones to avoid conflicts and you should be golden.
You don't say if your ISP is giving you an ip by VLANs on their side or PPOE - those need details in advance to set OPN on first.
Later you can move on to VLANs.
Then policy routing for VPNs.
Finally services like Suricata, Zenarmor, etc. I'd leave those for last.
Good luck in your new adventure.

Thanks for the advice. Let me clarify my network setup.

My NAS and main PC have a direct 2.5GbE connection. Both also connect to Switch 1 (managed Netgear, 1GbE).

Switch 2, near my ISP router, connects Sonos, WiFi, IoT devices, TVs, etc.

Currently, both switches are connected by a long Ethernet cable. I'd remove that connection and connect them directly to OPNsense:

- Port 1: WAN (ISP router)
- Port 2: Switch 1 (homelab)
- Port 3: Switch 2 (WiFi/IoT)
- Port 4: Spare

My goal is to isolate the homelab (VLAN 10) from WiFi/IoT (VLAN 20). Gigabit speeds are sufficient.

I'd prefer an established brand such as Protectli and an N305 CPU for future Suricata experiments.

The Protectli VP3230 has only two Intel i226-V ports, but apparently supports PCIe expansion:

https://kb.protectli.com/kb/vp3200-series-hardware-overview/

Would adding a dual-port Intel NIC through this expansion be a reliable solution for a 24/7 OPNsense firewall?

Or does anyone know of a good-quality, native four-port N305 mini PC that's readily available from Amazon or a reputable European retailer?

Thanks!

Quote from: sam1970 on November 16, 2026, 11:09:48 PM[...]The Protectli VP3230 has only two Intel i226-V ports, but apparently supports PCIe expansion:[...]

Looks like it trades storage for expansion. I'm too paranoid to rely on a non-replaceable EMMC (for anything besides booting a tiny ARM); I suppose you could rig the x1 M.2 slot for SATA and the x4 for network, but that would not leverage your existing SSDs. It's an inherent disadvantage of the Atom: not much in the way of expansion. I'd be tempted to look for a surplus office-type PC with similar specs, but you may not be willing to pay the power and size penalty - it's tough to match the N300s watt-for-watt.

Then again, you could use the x4 M.2 for storage and the x1 for network if you just need a single 2.5Gb or multiple 1Gb interfaces. I didn't look at the accessory cost to accomplish that.

@pfry
Thanks for the explanation. I'd rather keep proper NVMe storage than sacrifice it for additional network ports.

I've contacted Protectli to ask whether they have an affordable N305-based solution with four Intel NICs.

I'm not expecting much, though. I've also had ChatGPT search extensively for alternatives, but most suitable models seem to come from lesser-known Chinese brands, which I'd prefer to avoid.

If Protectli doesn't have a suitable solution, I'll probably put the project on hold for now and revisit it later.

Hopefully DDR5 RAM prices will be a bit more reasonable by then. :)

Thanks again for your advice!

@sam1970, while I think you have the right idea to get a more powerful CPU, I will say that even my Celeron based V1410 has no trouble at all with 2.5Gbit speeds port-to-port as long as multiple threads are used (e.g. -P2 or -P4 in iperf3).  For web traffic, I don't notice because my ISP speed is gigabit class anyway and the Celeron doesn't a break a sweat on that.  I don't run Suricata or ZA though, just routing & f/w.

For NAS traffic, I too keep it link-local and still benefit from VLANs at the switch level.

All that to say that unless you really are dead set on IDS/IDP, you can get away with a lot less than you might think. :)
N5105 | 8/250GB | 4xi226-V | Community

@OPNenthu
Thanks, you may well be right. For my gigabit home network, I probably don't need such a powerful CPU for routing and firewalling alone.

I'm still undecided about Suricata and Zenarmor. Do you think they offer enough value in a private home network to justify running them permanently?

That would also determine whether I should buy 8 GB or 16 GB RAM. If I only enable them occasionally to investigate network traffic or experiment, I assume 8 GB would be sufficient. For continuous use, especially both together, 16 GB seems more sensible.

Unfortunately, RAM prices have become ridiculously expensive. I've been considering this project since last year, and it doesn't look like prices will drop anytime soon. Otherwise, I'd probably wait a little longer. :)

Thanks again for sharing your experience!

November 17, 2026, 09:59:18 AM #10 Last Edit: November 17, 2026, 10:03:14 AM by meyergru
Quote from: sam1970 on November 16, 2026, 11:09:48 PM- Port 2: Switch 1 (homelab)
- Port 3: Switch 2 (WiFi/IoT)

Usually, you wouldn't do that. You'd have to use OpnSense as a bridge to connect Port 2 and Port 3. Even non-routed layer 2 packets would pass through the machine, which puts more load on it. In your case, when all VLANs are strictly confined to a specific switch, you can get away with it, though, since in that case, all traffic between the homelab and WiFi/IoT is layer 3, anyway.

How about this one: https://www.amazon.de/dp/B0F7QYBKTV, it uses DDR-5, though. You will be hard pressed to find current models with DDR-4.
Intel N100, 4* I226-V, 2* 82559, 16 GByte, 500 GByte NVME, Leox LXT-010H-D

1100 down / 450 up, Bufferbloat A+

November 17, 2026, 10:14:05 AM #11 Last Edit: November 17, 2026, 10:29:07 AM by OPNenthu
Quote from: sam1970 on November 17, 2026, 09:47:11 AMm still undecided about Suricata and Zenarmor. Do you think they offer enough value in a private home network to justify running them permanently?

As I've never used them and they aren't in my wheelhouse, I can't advise you on them.  Will leave that to the pros.

I will only say that I haven't yet felt like I'm missing anything for my home network needs.

For a pure F/W and a couple WG tunnels, I find 8GB is more than enough.  I'm using less than half of it.  Depends too on on how many alias table entries you keep.

EDIT: oh, I'm also not currently hosting so that makes it easy for me eschew an NGFW for now.  I think that's important to note.
N5105 | 8/250GB | 4xi226-V | Community

Quote from: meyergru on November 17, 2026, 09:59:18 AMHow about this one: https://www.amazon.de/dp/B0F7QYBKTV, it uses DDR-5, though. You will be hard pressed to find current models with DDR-4.

I have to scratch my head at some of these naming choices. lol
N5105 | 8/250GB | 4xi226-V | Community

November 17, 2026, 10:29:17 AM #13 Last Edit: November 17, 2026, 10:33:50 AM by yourfriendarmando
I prefer to use 4 or more port devices. You get your ports for WAN, LAN\Work, Guest and other lower priority networks, and the unused port, I usually designate as a MGT port.

This port can have the least access restrictions. It can be as useful to you as you need. In case you lock yourself out of the firewall, need to rule out if a rule at the DNS or IP level is blocking legitimate traffic.

The idea is based on the special management port found on larger servers that provides direct access to the system.

Also my experience shows less issues with Protectli brand mini PCs than with anything in similar category offered on Amazon. At least close to having one CPU core per network interface port to run.

RAM should be at minimum 8GB. Sometimes loading and parsing large block lists from external sources could put a load on resources.

If running IDS/IPS, definitely more RAM and CPU cores

November 17, 2026, 10:34:39 AM #14 Last Edit: November 17, 2026, 10:48:06 AM by tangofan
Quote from: sam1970 on November 16, 2026, 08:18:21 PM3. Based on your own experience, are there any better mini PCs you would recommend?
4. Which OPNsense plugins or features would you recommend for a homelab? I'm considering Suricata, Zenarmor, ntopng, WireGuard and policy-based routing through Proton VPN.
I am running OPNsense (with ZFS filesystem) on a Protectli VP2420, with a Celeron J6412, 16GB RAM and 4 i226-V NICs.

Since you mention Zenarmor: I ran it for two years (with a paid subscription) but recently I gave it up and uninstalled it. It runs only single-threaded and during an iperf test between different VLANs, the transfer speed without Zenarmor was 2.4Gbps (essentially line-speed of my i226-V NICs), but with Zenarmor transfer speed dropped to 1.1Gbps. Of course you are looking at a unit with a beefier CPU, but ensure that it has the single-core performance to get you the bandwidth you want from it with Zenarmor. I don't know anything about Suricata and its architecture, but look into performance requirements as well.

Furthermore, Zenarmor (and perhaps Suricata as well?) is a memory hog and I was glad at the time that I had 16GB of RAM, as my memory consumption was close to 8GB with Zenarmor and the other stuff. So 8GB probably won't cut it.

Quote5. Would you recommend keeping my existing Pi-hole installations, or would Unbound with DNS filtering in OPNsense be a good alternative? I'm also considering NetAlertX as a replacement for Fing for network device discovery.
Until yesterday I used Unbound with DNS-filtering as a DNS forwarder, so I could use DoT (since I live in the US and I trust my internet provider almost as much as a rattle snake). Today I actually installed the AdGuard plugin for OPNsense and trying that out. At the moment I don't even useUnbound, since I am using AdGuard as my local DNS server and DNS forwarder to upstream. I have no experience with Pi-Hole, so I can't comment on that. If you want a primary DNS resolver in your setup, then you would still use Unbound, either standalone or behind Pi-Hole or AdGuard in the request chain.
QuoteMy main priorities are reliable 24/7 operation, good firmware support and reasonable power consumption. I'm specifically looking for a compact mini PC, not a rackmount server.
I have been happy with my Protectli (since I noticed from a later post in the thread that Protectli is in discussion). I would recommend the Amibios though, not their coreboot BIOS. Re. resonable power consumption: If you go for a beefier CPU, I would assume that your overall power consumption will go up, so that might be  a consideration as well.