Bootreihenfolge geändert nach Update auf 26.1

[cottec]

Ich versteh die Welt nicht mehr....

Internet war die letzten Tage lahm, bzw das Wifi.
Habe mir gedacht, dass nach 3 Monaten einmal Reboot von Modem, Wifi AP, Switch und Protectli gut tun könnte.
Gesagt getan, hat sich aber alles super schwer getan, bis es dann lief.

Gestern Abend dann noch direkt auf 26.1 geupdated. Hat sich auch etwas schwer getan, hat ewig gedauert und hat irgendwie nicht gestartet.
Damit war ich laut Internet nicht der einzige und einen Powercycle später lief alles.
Hatte gestern Abend und heute Vormittag problemlos "Internet"

Vor 2 Stunden nach Hause gekommen, TV an "kein Internet"

Okay, PC an, mal in die Firwall schauen.
Wie kein Netzwerk?!?!?!

Alles tot...
Protectli ausgebaut und an nen Monitor gehangen, kein Bild und sie bootet auch nicht mit ihrem "Tralala Song", sie geht lediglich an.

Dann läuft auf meinem Win 11 die Com Verbindung zu meiner Protectli nicht, auf nem Win 10 Notebook lief es sofort (1 verschwendete Stunde und Bios Reset später)

In der Konsole festgestellt, dass er in irgendeinem Netzwerk Boot hängt. Ja komisch wieso das denn, der soll doch von der Festplatte booten.
Mal per Hand die Festplatte gebootet und zack fährt das Ding doch.

Bootreihenfolge wieder auf Festplatte zuerst. Aus An - Einwandfrei gebootet.



Was ist denn da bitte passiert?!?!

Edit: ist der Release von 26.1 noch nicht stable? Hab ich genau das Fenster abgepasst, nach Ewigkeiten mal wieder ein Update zu fahren, wenn ausgerechent 2 Tage davor die 26.1 erst ausgerollt wurde?

[Patrick M. Hausen]

Wenn ein Gerät vom Netz statt von der eingebauten Festplatte (? nicht doch eher ein Flash-Speicher oder eine SSD?) bootet, liegt das wohl kaum an OPNsense.

Die 26.1 hat noch ein paar Wehwehchen, aber größtenteils im UI und erst mal nicht im grundliegenden Betrieb. Vor allem, wenn du die Migration der Firewall-Regeln auf das neue UI erst mal bleiben lässt (muss man ausdrücklich und manuell machen) und auch den ISC-DHCPd, der automatisch als Plugin installiert wird, einfach weiter laufen lässt, dann ändert sich "eigentlich" erst mal gar nix.

[cottec]

Der ist auf irgendeinen Network Boot gesprungen, die Bootreihenfolge war auch falsch.
Vielleicht Bios Batterie leer?
Uhrzeit habe ich nicht gecheckt, muss ich mal tun...

Ich werde jetzt mal noch fix ne SSD bestellen und einbauen, dass ich ZFS verwenden kann, dann erspar ich mir zumindest etwas Ärger wenn ich mal bei der OPNsense zurückrollen will

[Patrick M. Hausen]

ZFS regelt.

[cottec]

hoffentlich...

aber hier ist total der wurm drin, ständig ausfälle, jetzt gerade wieder ein reboot, keine ahnung was da los ist.

stirbt mir etwa gerade der eMMC?

[Patrick M. Hausen]

Was sagt den "dmesg"? Was erscheint auf einer angeschlossenen Konsole? Wenn es ein Hardware-Problem ist, sollte es da Hinweise geben.

[cottec]

Basierend auf den von Ihnen hochgeladenen System-Logs lässt sich kein klassischer Systemabsturz (Kernel Panic) feststellen, sondern eher eine Kette von kritischen Hardware- und Konfigurationsproblemen, die das System instabil machen oder einen automatischen Neustart ausgelöst haben könnten.

Die Hauptgründe für die Instabilität sind:

1. Hardware-Fehler des Speichermediums (Kritisch)
Das schwerwiegendste Problem sind Hardware-Fehler beim Schreibzugriff auf das Boot-Medium (mmcsd0), bei dem es sich wahrscheinlich um eine SD-Karte oder ein eMMC-Modul handelt.

Fehlermeldungen: mmcsd0: Setting erase start position failed Timeout und g_vfs_done():gpt/rootfs[DELETE(...)]error = 5.

Bedeutung: Das Dateisystem meldet E/A-Fehler (I/O Errors). "Error 5" steht für einen Input/Output-Fehler. Dies deutet darauf hin, dass das Speichermedium defekt ist oder die Schreibzugriffe aufgrund von Timeouts fehlschlagen. Dies führt zwangsläufig zum "Einfrieren" oder unkontrollierten Neustart der OPNsense.

2. PPPoE-Verbindungsprobleme (Dauerhaft)
Das System versucht ununterbrochen, eine WAN-Verbindung über PPPoE aufzubauen, was scheitert.


Fehlermeldungen: PPPoE connection timeout after 9 seconds und zahlreiche reconnection attempt (bis zu Versuch 12 dokumentiert).
+2


Auswirkung: Da die OPNsense bei jedem gescheiterten Verbindungsaufbau versucht, Dienste wie den DNS-Server (Unbound), das Routing und Filterregeln neu zu konfigurieren, entsteht eine hohe Systemlast und Instabilität in der Konfigurations-Engine.
+2

3. Fehlerhafte Plugin-Konfigurationen
Es gibt mehrere Fehler bei Zusatzdiensten, die beim Systemstart (Bootup) zu Verzögerungen oder Fehlfunktionen führen:


ntopng: Der Dienst meldet Too many interfaces (8) und bricht die Initialisierung des Network Discovery ab. Es wird empfohlen, die Redis-Datenbank zurückzusetzen (redis-cli flushall).
+2


Backup-Fehler (Bitrix24/Rclone): Es treten kritische Fehler beim Versuch auf, Backups auf einen Cloud-Speicher hochzuladen (Failed to create file system [...] server misbehaving), da zu diesem Zeitpunkt keine Internetverbindung (DNS-Fehler) besteht.


NUT (USV-Überwachung): Der Dienst für die USV (Unterbrechungsfreie Stromversorgung) kann nicht starten, da keine Definitionen in der ups.conf gefunden wurden.

Zusammenfassung und Empfehlung: Der wahrscheinlichste Grund für "Abstürze" ist das defekte oder inkompatible Speichermedium (mmcsd0).

Hardware prüfen: Ersetzen Sie das Speichermedium (SD-Karte/eMMC) durch eine hochwertige SSD oder eine neue SD-Karte.

PPPoE prüfen: Stellen Sie sicher, dass das Modem korrekt verbunden ist und die Zugangsdaten stimmen, um die ständigen Neukonfigurationen zu stoppen.

Dienste bereinigen: Deaktivieren Sie testweise ntopng und die Cloud-Backups, bis die Basis-Internetverbindung stabil läuft.

[Patrick M. Hausen]

Was ist das? Wenn das "KI" ist - ok. Ich hatte dich nach der Ausgabe von "dmesg" gefragt, ich bin raus. Ich unterhalte mich nicht mit sogenannter "KI".

[cottec]

ich dachte dmesg ist das gleiche wie das syslog das ich vorher angehängt hatte.
Das mit der "KI" war nur auf den Teil des defekten eMMCs bezogen

Code Select Expand

---<<BOOT>>---
Copyright (c) 1992-2023 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 14.3-RELEASE-p7 stable/26.1-n271965-1bab7230df71 SMP amd64
FreeBSD clang version 19.1.7 (https://github.com/llvm/llvm-project.git llvmorg-19.1.7-0-gcd708029e0b2)
[1] VT(vga): resolution 640x480
[1] CPU: Intel(R) Celeron(R) N5105 @ 2.00GHz (1996.80-MHz K8-class CPU)
[1]   Origin="GenuineIntel"  Id=0x906c0  Family=0x6  Model=0x9c  Stepping=0
[1]   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
[1]   Features2=0x4ff8ebbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,RDRAND>
[1]   AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
[1]   AMD Features2=0x101<LAHF,Prefetch>
[1]   Structured Extended Features=0x2394a2c3<FSGSBASE,TSCADJ,FDPEXC,SMEP,ERMS,NFPUSG,PQE,RDSEED,SMAP,CLFLUSHOPT,CLWB,PROCTRACE,SHA>
[1]   Structured Extended Features2=0x18400124<UMIP,WAITPKG,GFNI,RDPID,MOVDIRI,MOVDIR64B>
[1]   Structured Extended Features3=0xfc000400<MD_CLEAR,IBPB,STIBP,L1DFL,ARCH_CAP,CORE_CAP,SSBD>
[1]   XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
[1]   IA32_ARCH_CAPS=0x14020c6b<RDCL_NO,IBRS_ALL,SKIP_L1DFL_VME,MDS_NO>
[1]   VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr
[1]   TSC: P-state invariant, performance statistics
[1] real memory  = 8589934592 (8192 MB)
[1] avail memory = 8120631296 (7744 MB)
[1] Event timer "LAPIC" quality 600
[1] ACPI APIC Table: <COREv4 COREBOOT>
[1] WARNING: L1 data cache covers fewer APIC IDs than a core (0 < 1)
[1] FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
[1] FreeBSD/SMP: 1 package(s) x 4 core(s)
[1] random: registering fast source Intel Secure Key RNG
[1] random: fast provider: "Intel Secure Key RNG"
[1] random: unblocking device.
[1] ioapic0 <Version 2.0> irqs 0-119
[1] Launching APs: 1 3 2
[1] random: entropy device external interface
[1] wlan: mac acl policy registered
[1] kbd0 at kbdmux0
[1] WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 15.0.
[1] efirtc0: <EFI Realtime Clock>
[1] efirtc0: registered as a time-of-day clock, resolution 1.000000s
[1] smbios0: <System Management BIOS> at iomem 0x78332000-0x78332017
[1] smbios0: Entry point: v3 (64-bit), Version: 3.3
[1] aesni0: <AES-CBC,AES-CCM,AES-GCM,AES-ICM,AES-XTS,SHA1,SHA256>
[1] acpi0: <COREv4 COREBOOT>
[1] acpi0: Power Button (fixed)
[1] hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
[1] Timecounter "HPET" frequency 19200000 Hz quality 950
[1] Event timer "HPET" frequency 19200000 Hz quality 550
[1] Event timer "HPET1" frequency 19200000 Hz quality 440
[1] Event timer "HPET2" frequency 19200000 Hz quality 440
[1] Event timer "HPET3" frequency 19200000 Hz quality 440
[1] Event timer "HPET4" frequency 19200000 Hz quality 440
[1] atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
[1] atrtc0: registered as a time-of-day clock, resolution 1.000000s
[1] Event timer "RTC" frequency 32768 Hz quality 0
[1] attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
[1] Timecounter "i8254" frequency 1193182 Hz quality 0
[1] Event timer "i8254" frequency 1193182 Hz quality 100
[1] Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
[1] acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
[1] pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
[1] pci0: <ACPI PCI bus> on pcib0
[1] vgapci0: <VGA-compatible display> port 0x1000-0x103f mem 0x90000000-0x90ffffff,0x80000000-0x8fffffff at device 2.0 on pci0
[1] vgapci0: Boot video device
[1] xhci0: <XHCI (generic) USB 3.0 controller> mem 0x91500000-0x9150ffff at device 20.0 on pci0
[1] xhci0: 32 bytes context size, 64-bit DMA
[1] usbus0 on xhci0
[1] usbus0: 5.0Gbps Super Speed USB v3.0
[1] pci0: <memory, RAM> at device 20.2 (no driver attached)
[1] pci0: <simple comms> at device 22.0 (no driver attached)
[1] sdhci_pci0: <Generic SD HCI> mem 0x91518000-0x91518fff at device 26.0 on pci0
[1] sdhci_pci0: 1 slot(s) allocated
[1] mmc0: <MMC/SD bus> on sdhci_pci0
[1] pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
[1] pci1: <ACPI PCI bus> on pcib1
[1] igc0: <Intel(R) Ethernet Controller I226-V> mem 0x7fc00000-0x7fcfffff,0x7fd00000-0x7fd03fff at device 0.0 on pci1
[1] igc0: EEPROM V2.13-0 eTrack 0x80000286
[1] igc0: Using 1024 TX descriptors and 1024 RX descriptors
[1] igc0: Using 4 RX queues 4 TX queues
[1] igc0: Using MSI-X interrupts with 5 vectors
[1] igc0: Ethernet address: 64:62:66:2f:0f:0a
[1] igc0: netmap queues/slots: TX 4/1024, RX 4/1024
[1] pcib2: <ACPI PCI-PCI bridge> at device 28.1 on pci0
[1] pci2: <ACPI PCI bus> on pcib2
[1] igc1: <Intel(R) Ethernet Controller I226-V> mem 0x7fe00000-0x7fefffff,0x7ff00000-0x7ff03fff at device 0.0 on pci2
[1] igc1: EEPROM V2.13-0 eTrack 0x80000286
[1] igc1: Using 1024 TX descriptors and 1024 RX descriptors
[1] igc1: Using 4 RX queues 4 TX queues
[1] igc1: Using MSI-X interrupts with 5 vectors
[1] igc1: Ethernet address: 64:62:66:2f:0f:0b
[1] igc1: netmap queues/slots: TX 4/1024, RX 4/1024
[1] pcib3: <ACPI PCI-PCI bridge> at device 28.5 on pci0
[1] pci3: <ACPI PCI bus> on pcib3
[1] igc2: <Intel(R) Ethernet Controller I226-V> mem 0x91000000-0x910fffff,0x91100000-0x91103fff at device 0.0 on pci3
[1] igc2: EEPROM V2.13-0 eTrack 0x80000286
[1] igc2: Using 1024 TX descriptors and 1024 RX descriptors
[1] igc2: Using 4 RX queues 4 TX queues
[1] igc2: Using MSI-X interrupts with 5 vectors
[1] igc2: Ethernet address: 64:62:66:2f:0f:0c
[1] igc2: netmap queues/slots: TX 4/1024, RX 4/1024
[1] pcib4: <ACPI PCI-PCI bridge> at device 28.6 on pci0
[1] pci4: <ACPI PCI bus> on pcib4
[1] igc3: <Intel(R) Ethernet Controller I226-V> mem 0x91200000-0x912fffff,0x91300000-0x91303fff at device 0.0 on pci4
[1] igc3: EEPROM V2.13-0 eTrack 0x80000286
[1] igc3: Using 1024 TX descriptors and 1024 RX descriptors
[1] igc3: Using 4 RX queues 4 TX queues
[1] igc3: Using MSI-X interrupts with 5 vectors
[1] igc3: Ethernet address: 64:62:66:2f:0f:0d
[1] igc3: netmap queues/slots: TX 4/1024, RX 4/1024
[1] isab0: <PCI-ISA bridge> at device 31.0 on pci0
[1] isa0: <ISA bus> on isab0
[1] hdac0: <Intel Jasper Lake HDA Controller> mem 0x91510000-0x91513fff,0x91400000-0x914fffff at device 31.3 on pci0
[1] pci0: <serial bus> at device 31.5 (no driver attached)
[1] cpu0: <ACPI CPU> on acpi0
[1] ns8250: UART FCR is broken
[1] ns8250: UART FCR is broken
[1] uart0: <16550 or compatible> at port 0x3f8 irq 4 flags 0x10 on isa0
[1] ns8250: UART FCR is broken
[1] uart0: console (115200,n,8,1)
[1] est0: <Enhanced SpeedStep Frequency Control> on cpu0
[1] cpufreq0: <CPU frequency control> on cpu0
[1] cpufreq1: <CPU frequency control> on cpu1
[1] cpufreq2: <CPU frequency control> on cpu2
[1] cpufreq3: <CPU frequency control> on cpu3
[1] Timecounter "TSC" frequency 1996804504 Hz quality 1000
[1] Timecounters tick every 1.000 msec
[1] ugen0.1: <Intel XHCI root HUB> at usbus0
[1] uhub0 on usbus0
[1] uhub0: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[1] mmcsd0: 31GB <MMCHC BJTD4R 0.3 SN 78F5FEBD MFG 08/2023 by 21 0x0000> at mmc0 200.0MHz/8bit/8192-block
[1] mmcsd0boot0: 4MB partition 1 at mmcsd0
[1] mmcsd0boot1: 4MB partition 2 at mmcsd0
[1] mmcsd0rpmb: 4MB partition 3 at mmcsd0
[1] hdacc0: <Intel Jasper Lake HDA CODEC> at cad 2 on hdac0
[1] hdaa0: <Intel Jasper Lake Audio Function Group> at nid 1 on hdacc0
[1] pcm0: <Intel Jasper Lake (HDMI/DP 8ch)> at nid 4 on hdaa0
[1] Trying to mount root from ufs:/dev/gpt/rootfs [rw,noatime]...
[1] WARNING: / was not properly dismounted
[1] WARNING: /: mount pending error: blocks 72 files 3
[1] Dual Console: Serial Primary, Video Secondary
[1] uhub0: 14 ports with 14 removable, self powered
[2] ugen0.2: <VIA Labs, Inc. USB2.0 Hub> at usbus0
[2] uhub1 on uhub0
[2] uhub1: <VIA Labs, Inc. USB2.0 Hub, class 9/0, rev 2.10/0.50, addr 1> on usbus0
[2] uhub1: MTT enabled
[4] uhub1: 4 ports with 4 removable, self powered
[4] ugen0.3: <VIA Labs, Inc. USB3.0 Hub> at usbus0
[4] uhub2 on uhub0
[4] uhub2: <VIA Labs, Inc. USB3.0 Hub, class 9/0, rev 3.10/0.50, addr 2> on usbus0
[6] uhub2: 4 ports with 4 removable, self powered
[9] igc1: link state changed to UP
[9] igc2: link state changed to UP
[9] igc3: link state changed to UP
[12] lo0: link state changed to UP
[12] coretemp0: <CPU On-Die Thermal Sensors> on cpu0
[14] igc2: link state changed to DOWN
[14] lagg0: link state changed to DOWN
[14] igc3: link state changed to DOWN
[14] vlan0: changing name to 'vlan01'
[14] vlan1: changing name to 'vlan02'
[14] igc1: link state changed to DOWN
[14] wg0: link state changed to UP
[15] ng0: changing name to 'pppoe0'
[17] igc3: link state changed to UP
[17] igc2: link state changed to UP
[17] igc1: link state changed to UP
[22] lagg0: link state changed to UP
[22] vlan02: link state changed to UP
[22] vlan01: link state changed to UP
[127] igc1: promiscuous mode enabled
[127] igc2: promiscuous mode enabled
[127] igc3: promiscuous mode enabled
[127] lagg0: promiscuous mode enabled
[127] vlan02: promiscuous mode enabled
[127] pppoe0: promiscuous mode enabled
[127] vlan01: promiscuous mode enabled
[127] wg0: promiscuous mode enabled
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15666479104, length=19660mmcsd0: Setting erase start position failed Timeout
[14100] 80)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15669100544, length=49152mmcsd0: Setting erase start position failed Timeout
[14100] 0)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15671099392, length=10485mmcsd0: Setting erase start position failed Timeout
[14100] 76)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15673655296, length=91750mmcsd0: Setting erase start position failed Timeout
[14100] 4)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15681388544, length=52428mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15682797568, length=52428mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15692169216, length=10485mmcsd0: Setting erase start position failed Timeout
[14100] 76)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15698984960, length=52428mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15703736320, length=10485mmcsd0: Setting erase start position failed Timeout
[14100] 76)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15705341952, length=62259mmcsd0: Setting erase start position failed Timeout
[14100] 2)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15706652672, length=19988mmcsd0: Setting erase start position failed Timeout
[14100] 48)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15714222080, length=1048576)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15722348544, length=524288)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15723495424, length=1048576)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15726673920, length=884736)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15729721344, length=10485mmcsd0: Setting erase start position failed Timeout
[14100] 76)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15806758912, length=52428mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15840706560, length=72089mmcsd0: Setting erase start position failed Timeout
[14100] 6)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15877603328, length=58982mmcsd0: Setting erase start position failed Timeout
[14100] 4)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15883763712, length=72089mmcsd0: Setting erase start position failed Timeout
[14100] 6)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15888875520, length=81920mmcsd0: Setting erase start position failed Timeout
[14100] 0)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15919546368, length=20971mmcsd0: Setting erase start position failed Timeout
[14100] 52)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15975776256, length=85196mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15978102784, length=52428mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=15988817920, length=10485mmcsd0: Setting erase start position failed Timeout
[14100] 76)]error = 5
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=16042426368, length=52428mmcsd0: Setting erase start position failed Timeout
[14100] 8)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=16044654592, length=10485mmcsd0: Setting erase start position failed Timeout
[14100] 76)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] g_vfs_done():gpt/rootfs[DELETE(offset=16048226304, length=12451mmcsd0: Setting erase start position failed Timeout
[14100] 84)]error = 5
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14100] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=16069853184, length=55771mmcsd0: Setting erase start position failed Timeout
[14101] 136)]error = 5
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=23345561600, length=41615mmcsd0: Setting erase start position failed Timeout
[14101] 36)]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789429760, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789528064, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789593600, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789659136, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789757440, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789822976, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789855744, length=32768)]error = 5
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13789986816, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13790019584, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13790085120, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13874397184, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13875085312, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13900021760, length=16384mmcsd0: Setting erase start position failed Timeout
[14101] 0)]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13911523328, length=32768)]error = 5
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13914210304, length=32768)]error = 5
[14101] mmcsd0: Setting erase start position failed Timeout
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=13918404608, length=32768mmcsd0: Setting erase start position failed Timeout
[14101] )]error = 5
[14101] g_vfs_done():gpt/rootfs[DELETE(offset=14132641792, length=196608)]error = 5
[14103] mmcsd0: Error indicated: 1 Timeout
[14103] g_vfs_done(): gpt/rootfs converting all errors to ENXIO
[14103] mmcsd0: Error indicated: 1 Timeout
[14103] g_vfs_done():gpt/rootfs[WRITE(offset=32621568, length=512)]error = 6 supressing further ENXIO
[14103] panic: UFS: root fs would be forcibly unmounted
[14103] cpuid = 1
[14103] time = 1769979720
[14103] KDB: stack backtrace:
[14103] db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xfffffe0085059c20
[14103] vpanic() at vpanic+0x161/frame 0xfffffe0085059d50
[14103] panic() at panic+0x43/frame 0xfffffe0085059db0
[14103] ffs_fsfail_cleanup() at ffs_fsfail_cleanup+0x11e/frame 0xfffffe0085059de0
[14103] softdep_disk_write_complete() at softdep_disk_write_complete+0x45/frame 0xfffffe0085059e40
[14103] bufdone() at bufdone+0x1f2/frame 0xfffffe0085059ea0
[14103] g_io_schedule_up() at g_io_schedule_up+0xea/frame 0xfffffe0085059ee0
[14103] g_up_procbody() at g_up_procbody+0x6c/frame 0xfffffe0085059ef0
[14103] fork_exit() at fork_exit+0x81/frame 0xfffffe0085059f30
[14103] fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe0085059f30
[14103] --- trap 0, rip = 0, rsp = 0, rbp = 0 ---
[14103] KDB: enter: panic