Problem upgrading to 25.7.3

[ldanna1945]

Tried to upgrade to 25.7.3  . each time when the status shows as follows


Installed packages to be UPGRADED:
   opnsense: 25.7.2 -> 25.7.3_7 [OPNsense]
   os-sensei: 2.0.7 -> 2.0.8 [SunnyValley]

Number of packages to be upgraded: 2
[1/2] Upgrading os-sensei from 2.0.7 to 2.0.8...
[1/2] Extracting os-sensei-2.0.8: .........

then unit reboots and doesn't complete upgrade

Tried to do upgrade multiple times with no success

Any ideas on why this is happening

?

Larry

[BrandyWine]

Run the audit in gui, lets see what that says.

[ldanna1945]

Here is a sampling of what I found
The .35 address is my computer no other devices on this LAN
All the errors have the same no active user etc.

2025-09-13T16:38:52Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:52Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:51Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:51Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:40Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:38Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:38Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:28Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:38:28Errorauditno active session, user not found (called "/favicon.ico" @ 192.168.1.35)
2025-09-13T16:37:58Errorauditno active session, user not found (called "/ui/core/dashboard" @ 192.168.1.35)
2025-09-13T16:37:50Errorauditno active session, user not found (called "/api/diagnostics/system/system_time" @ 192.168.1.35)
2025-09-13T16:37:50Errorauditno active session, user not found (called "/api/diagnostics/traffic/interface" @ 192.168.1.35)
2025-09-13T16:37:40Errorauditno active session, user not found (called "/api/routing/settings/search_gateway" @ 192.168.1.35)
2025-09-13T16:37:40Errorauditno active session, user not found (called "/api/core/service/search" @ 192.168.1.35)
2025-09-13T16:37:40Errorauditno active session, user not found (called "/api/diagnostics/system/system_time" @ 192.168.1.35)
2025-09-13T16:37:40Errorauditno active session, user not found (called "/api/diagnostics/traffic/interface" @ 192.168.1.35)
2025-09-13T16:37:31Errorauditno active session, user not found (called "/api/routing/settings/search_gateway" @ 192.168.1.35)
2025-09-13T16:37:31Errorauditno active session, user not found (called "/api/core/service/search" @ 192.168.1.35)
2025-09-13T16:37:31Errorauditno active session, user not found (called "/api/diagnostics/system/system_resources" @ 192.168.1.35)
2025-09-13T16:37:31Errorauditno active session, user not found (called "/api/diagnostics/system/system_time" @ 192.168.1.35)

[ldanna1945]

Just tried a fresh install.  Install went fine. Then I went to update the system. obviously it found many to update.
on the first update when working on extracting first file it crashed and rebooted. tried again same result. Note: same behavior when I tried to update first installation to 27.7.3
Any Ideas??

[ldanna1945]

Update:

Tried to do update again. Looked good so far lots of stuff upgraded no problem at this point . then checked for updates system may have missed . only Base and kernal both came up. I told it to update then system again rebooted in middle but this time system is corrupted and will not boot up into operating system anymore
Pulling out hair at this point

LArry

[ldanna1945]

more update:
  on console i tried a show panic
got  mountroot unable to (re-) mount root.

Where to go from here

[ldanna1945]

Success update:

After several reinstalls last one was successful. Not sure what made it work only it does now
Any insight to why this was such a painful and long process?

Larry

[Patrick M. Hausen]

Are you running on an N100 or comparable CPU? Are you using UFS?

Try to install with ZFS - there is really no reason not to.

[ldanna1945]

Unit is a Protectli FW6d
\Intel i5 8250U Quad Core with Hyperthreading (8 threads) at up to 3.4GHz (turbo boost)
Also running ZFS
Larry

[BrandyWine]

Unit is a Protectli FW6d
\Intel i5 8250U Quad Core with Hyperthreading (8 threads) at up to 3.4GHz (turbo boost)
Also running ZFS
Larry

I will leave it up to you to read-up on, but should HT be enabled or disabled?
You can start here https://forum.opnsense.org/index.php?topic=42974.0

As of now my N150 has HT disabled.