Author Topic: tuneables - do they work? - eee and smart power down (Read 4129 times)

ArminF · « **on:** February 13, 2020, 08:33:22 pm »

Aloha,
one of my nics do often goes down. Link is down and i cannot watch Netflix anymore.

I think it is a power option on the nic as the TV is usually used in the evening and during the day its on standby.
So opnsense decides to shutdown the nic.

found this settings on the cli
dev.igb.3.eee_disabled: 0
dev.igb.2.eee_disabled: 0
dev.igb.1.eee_disabled: 0
dev.igb.0.eee_disabled: 0
hw.em.smart_pwr_down: 0

would 1 disable or enable them? I think its worth a try.
Ah.. Nic is a 4 Port Intel211 and i found a lot to read here and on google.

So my plan is to start disabling the settings through tuneables.

thanks
armin

ArminF · « **Reply #1 on:** February 15, 2020, 02:22:29 pm »

Did a test and set all the tuneables in the system config page.
Zero seems to be default "off".

New
dev.igb.3.eee_disabled: 1
dev.igb.2.eee_disabled: 1
dev.igb.1.eee_disabled: 1
dev.igb.0.eee_disabled: 1
hw.em.smart_pwr_down: 1

Saved and rebooted the machine.
Yesterday and today the NIC did not decide to go offline.
Keep fingers crossed...

A

ArminF · « **Reply #2 on:** February 16, 2020, 11:56:19 am »

So wife is not happy.. Yesterday the NIC went offline again.

Workaround is to unplug the cable switch on the device (android TV) and connect back.
All is working again.

Do this tuneables be loaded into the loader config or do i have to set the deeper in the FreeBSD?

thanks
armin

ArminF · « **Reply #3 on:** February 16, 2020, 12:51:17 pm »

Well,
as i am lazy i did setup a cron with a periodic interface reset on my LAN3.
Maybe this will take the trouble off....

miroco · « **Reply #4 on:** February 16, 2020, 02:41:36 pm »

Did you try to switch out the network cable?

miroco

ArminF · « **Reply #5 on:** February 16, 2020, 04:11:08 pm »

hm.. not yet.
Not sure what the cable should have to do with it.

When you unplug and plug back in the card and connection works.

miroco · « **Reply #6 on:** February 16, 2020, 09:31:15 pm »

If you are running your OPNsense on a decent piece of hardware and don't have problems with other connected devices, you are in my view left with two suspects. The cable and a consumer product, the TV set itself.

miroco

ArminF · « **Reply #7 on:** February 17, 2020, 07:22:03 am »

miroco,

thanks! Will give it a try be in the lab today anyway and get some new cables.
CAT6 STFP. Just need to find some cool colours.

A

ArminF · « **Reply #8 on:** February 17, 2020, 08:56:20 pm »

So... installed a brandnew "purple" cat6 STP cable.

And today we had no issues. OK i left the cronjob on which resets the interface twice a day.

A

Author Topic: tuneables - do they work? - eee and smart power down (Read 4129 times)

ArminF

tuneables - do they work? - eee and smart power down

ArminF

Re: tuneables - do they work? - eee and smart power down

ArminF

Re: tuneables - do they work? - eee and smart power down

ArminF

Re: tuneables - do they work? - eee and smart power down

miroco

Re: tuneables - do they work? - eee and smart power down

ArminF

Re: tuneables - do they work? - eee and smart power down

miroco

Re: tuneables - do they work? - eee and smart power down

ArminF

Re: tuneables - do they work? - eee and smart power down

ArminF

Re: tuneables - do they work? - eee and smart power down