SERIAL Image - Keine Ausgabe

[lenny]

Hallo,
ich habe das Serial Image auf einen USB Stick geschrieben. Das System fährt hoch und ist im Abschluss per IP ansprechbar.

Jedoch erhalte ich keine Ausgabe über den Serial Port.
Grundsätzlich funktioniert das System (lief IPfire drauf) und das Notebook (Com1 - 115200 bit)
Das System hat zwei COM Anschlüsse, auf keinem erfolgt eine Ausgabe.

Nimmt man anstelle der OPN, Ipfire auf dem System, funktioniert es.
Daher schließe ich Kabel und Notebook erstmal aus.

Gibts Ideen oder Erfahrungen?

[guest17762]

[...]
Jedoch erhalte ich keine Ausgabe über den Serial Port.
[...]

Passiert denn etwas, wenn du ENTER drückst?
Wie verbindest du dich? Windows + Putty? Oder Linux bzw. via Screen?

[fabian]

Wenn er schreibt, dass es com1 ist, ist es Windows. Baud stimmt also würde ich mal in den erweiterten Einstellungen mal die Konfiguration des Serial Ports prüfen. Eine Änderung hier braucht aber einen Reboot.

[lenny]

Es ist Windows 10 mit PuTTY.
Baudrate ist gemäß Web Frontend eingestellt.
Analog zur ipfire, dort funktioniert es.

Enter drücken bringt keinen Erfolg.
Auch kein Wechsel der beiden seriellen Anschlüsse an der Firewall selber.

Als Kabel wird ein original Checkpoint Kabel verwendet.
(Das macht hoffentlich kein layer7 Check )

Gibt's spezielle Einstellungen für die opn?

[fabian]

Zumindest bei mir auf der APU habe ich gar nichts eingestellt.

[lenny]

per Fire gehts...:

[bobbis]

Verbose boot aktivieren mit boot -v am loader prompt und mal die Ausgabe von dmesg posten, die korrekten Einstellungen für den Seriellen Port sind : 115200/8/N/1 ,dies mal ggf. im Putty überprüfen.

[lenny]

hier der auszug.
bisher gehts leider nicht...

root@OPNsense:~ # dmesg
Copyright (c) 2013-2018 The HardenedBSD Project.
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.2-RELEASE-p16-HBSD  87a7fc985c3(stable/19.7) amd64
FreeBSD clang version 6.0.0 (tags/RELEASE_600/final 326565) (based on LLVM 6.0.0)
VT: init without driver.
HardenedBSD: initialize and check features (__HardenedBSD_version 1100056 __FreeBSD_version 1102000).
CPU: Intel(R) Celeron(R) CPU  N2810  @ 2.00GHz (2000.06-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x30673  Family=0x6  Model=0x37  Stepping=3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x43d8e3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,AESNI,RDRAND>
  AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
  AMD Features2=0x101<LAHF,Prefetch>
  Structured Extended Features=0x2282<TSCADJ,SMEP,ERMS,NFPUSG>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
  TSC: P-state invariant, performance statistics
real memory  = 4294967296 (4096 MB)
avail memory = 3969581056 (3785 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I >
WARNING: L1 data cache covers less APIC IDs than a core
0 < 1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
Firmware Warning (ACPI): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20171214/tbfadt-748)
ioapic0 <Version 2.0> irqs 0-86 on motherboard
SMP: AP CPU #1 Launched!
Timecounter "TSC" frequency 2000056650 Hz quality 1000
random: entropy device external interface
wlan: mac acl policy registered
000.000017 [4213] netmap_init               netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff8114aef0, 0) error 19
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
kbd1 at kbdmux0
nexus0
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I > on motherboard
acpi0: Power Button (fixed)
unknown: I/O range not supported
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: Warning: Couldn't map I/O.
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 8 on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: _OSC returned error 0x10
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xf080-0xf087 mem 0xd0000000-0xd03fffff,0xc0000000-0xcfffffff irq 16 at device 2.0 on pci0
vgapci0: Boot video device
ahci0: <AHCI SATA controller> port 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf020-0xf03f mem 0xd0916000-0xd09167ff irq 19 at device 19.0 on pci0
ahci0: AHCI v1.30 with 2 3Gbps ports, Port Multiplier not supported
xhci0: <Intel BayTrail USB 3.0 controller> mem 0xd0900000-0xd090ffff irq 20 at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
xhci0: Port routing mask set to 0xffffffff
usbus0 on xhci0
usbus0: 5.0Gbps Super Speed USB v3.0
pci0: <encrypt/decrypt> at device 26.0 (no driver attached)
hdac0: <Intel BayTrail HDA Controller> mem 0xd0910000-0xd0913fff irq 22 at device 27.0 on pci0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib1: [GIANT-LOCKED]
pci1: <ACPI PCI bus> on pcib1
re0: <Realtek PCIe GBE Family Controller> port 0xe000-0xe0ff mem 0xd0804000-0xd0804fff,0xd0800000-0xd0803fff irq 16 at device 0.0 on pci1
re0: Using Memory Mapping!
re0: Using 1 MSI-X message
re0: ASPM disabled
re0: version:1.95.00
re0: Ethernet address: XXXXXXXXXXXXXXXXxx

This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
re0: Ethernet address: XXXXXXXXXXXX
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pcib2: [GIANT-LOCKED]
pci2: <ACPI PCI bus> on pcib2
re1: <Realtek PCIe GBE Family Controller> port 0xd000-0xd0ff mem 0xd0704000-0xd0704fff,0xd0700000-0xd0703fff irq 17 at device 0.0 on pci2
re1: Using Memory Mapping!
re1: Using 1 MSI-X message
re1: ASPM disabled
re1: version:1.95.00
re1: Ethernet addressXXXXXXXXXXXX

This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
re1: Ethernet address: XXXXXXXXXXXXXXXXX
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pcib3: [GIANT-LOCKED]
pci3: <ACPI PCI bus> on pcib3
ath0: <Atheros 9280> mem 0xd0600000-0xd060ffff irq 18 at device 0.0 on pci3
ath0: [HT] enabling HT modes
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 stream STBC transmit enabled
ath0: [HT] 2 RX streams; 2 TX streams
ath0: AR9280 mac 128.2 RF5133 phy 13.0
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
pcib4: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pcib4: [GIANT-LOCKED]
ehci0: <Intel BayTrail USB 2.0 controller> mem 0xd0915000-0xd09153ff irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci0
usbus1: 480Mbps High Speed USB v2.0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
uart2: <16550 or compatible> port 0x3e0-0x3e7 irq 4 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc1: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 5 drq 3 on acpi0
ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc1: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc1
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
Timecounters tick every 1.000 msec
hdacc0: <Realtek ALC662 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC662 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC662 (Front Analog)> at nid 20 and 24 on hdaa0
pcm1: <Realtek ALC662 (Rear Digital)> at nid 30 on hdaa0
hdacc1: <Intel (0x2882) HDA CODEC> at cad 2 on hdac0
hdaa1: <Intel (0x2882) Audio Function Group> at nid 1 on hdacc1
pcm2: <Intel (0x2882) (HDMI/DP 8ch)> at nid 4 on hdaa1
pcm3: <Intel (0x2882) (HDMI/DP 8ch)> at nid 5 on hdaa1
ugen1.1: <Intel EHCI root HUB> at usbus1
ugen0.1: <0x8086 XHCI root HUB> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub1: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
Trying to mount root from ufs:/dev/ufs/OPNsense_Nano [rw]...
Root mount waiting for: usbus1 usbus0
uhub1: 7 ports with 7 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen0.2: <vendor 0x05e3 USB2.0 Hub> at usbus0
uhub2 on uhub1
uhub2: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/85.36, addr 1> on usbus0
uhub2: 4 ports with 4 removable, self powered
Root mount waiting for: usbus1 usbus0
Root mount waiting for: usbus1 usbus0
uhub0: 8 ports with 8 removable, self powered
ugen0.3: <Kingston DT Rubber 3.0> at usbus0
umass0 on uhub1
umass0: <Kingston DT Rubber 3.0, class 0/0, rev 3.00/1.00, addr 2> on usbus0
umass0:  SCSI over Bulk-Only; quirks = 0xc100
umass0:0:0: Attached to scbus0
(probe0:umass-sim0:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 00
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: ILLEGAL REQUEST asc:24,0 (Invalid field in CDB)
(probe0:umass-sim0:0:0:0): Error 22, Unretryable error
da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
da0: <Kingston DT Rubber 3.0 1.01> Removable Direct Access SPC-4 SCSI device
da0: Serial Number 00018F30C9EBFACC0800000A0
da0: 400.000MB/s transfers
da0: 15008MB (30736384 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
ugen1.2: <vendor 0x8087 product 0x07e6> at usbus1
uhub3 on uhub0
uhub3: <vendor 0x8087 product 0x07e6, class 9/0, rev 2.00/0.10, addr 2> on usbus1
uhub3: 4 ports with 4 removable, self powered
mountroot: waiting for device /dev/ufs/OPNsense_Nano...
random: unblocking device.
aesni0: <AES-CBC,AES-XTS,AES-GCM,AES-ICM> on motherboard
wlan0: Ethernet address: c4:17:fe:7e:34:ed
wlan0: changing name to 'ath0_wlan1'
re0: link state changed to UP
re1: link state changed to UP
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
ath0: ath_legacy_rx_tasklet: sc_inreset_cnt > 0; skipping
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
arp: 10XXXXXXXXxx3 moved from dcXXXXXXXXX on re0
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
tun1: changing name to 'ovpns1'
ovpns1: link state changed to UP
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
pflog0: promiscuous mode disabled
pflog0: promiscuous mode enabled
arp: 1.XXXXXXXXXX3 moved from XXXXXXXXXXXXX on re0
root@OPNsense:~ #