1
16.1 Legacy Series / Re: Slow download speed after upgrade to 16.1
« on: February 06, 2016, 02:28:04 pm »
Unfortunately, these steps didn't change anything for me... I still get slow speed.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
16.1 Legacy Series / Re: Slow download speed after upgrade to 16.1
« on: February 05, 2016, 11:30:52 am »
Yes, I did reboot the machine after making the changes.
3
16.1 Legacy Series / Re: Slow download speed after upgrade to 16.1
« on: February 05, 2016, 11:15:27 am »
I tried to disable all of them (except the VLAN filtering which seems to be required) and nothing changed.
4
16.1 Legacy Series / Slow download speed after upgrade to 16.1
« on: February 04, 2016, 06:48:24 pm »
I'm running opnsense on VirtualBox VM using virtio-net adapters. My wan is on a VLAN and traffic shaping is disabled. After upgrading to 16.1, I noticed that download speed from the internet was slow: Less than 1mbps, while with 15.7 I had around 20mbps.
Resetting and restoring my config didn't help. I also tried to configure only the minimum required to get a connection: same thing.
I re-installed 5.7 and download speed came back to normal (20mbps).
Is there any known issue that could explain this behavior?
Resetting and restoring my config didn't help. I also tried to configure only the minimum required to get a connection: same thing.
I re-installed 5.7 and download speed came back to normal (20mbps).
Is there any known issue that could explain this behavior?
5
15.7 Legacy Series / Re: [SOLVED] Can't upgrade freshly installed nano 15.7 to 15.7.7 on ALIX
« on: August 31, 2015, 12:12:44 pm »
It's a 256MB Alix. So from what I understand, I should consider an hardware upgrade 
.
In the meantime, I will re-flash with the new image.
.In the meantime, I will re-flash with the new image.
6
15.7 Legacy Series / Re: [SOLVED] Can't upgrade freshly installed nano 15.7 to 15.7.7 on ALIX
« on: August 28, 2015, 05:35:33 pm »
Once rebooted, the whole kernel upgrade always works. So I think that there is not enough space in the ram partition because of packages that were upgraded before. Maybe more stuff needs to be cleaned up?
Here is the requested output. Note that the device is currently not in a state where kernel cannot be upgraded.
root@router:~ # df -h
Filesystem Size Used Avail Capacity Mounted on
/dev/ufs/OPNsense0 936M 734M 127M 85% /
devfs 1.0K 1.0K 0B 100% /dev
tmpfs 13M 372K 13M 3% /tmp
tmpfs 39M 26M 13M 68% /var
devfs 1.0K 1.0K 0B 100% /var/dhcpd/dev
Here is the requested output. Note that the device is currently not in a state where kernel cannot be upgraded.
root@router:~ # df -h
Filesystem Size Used Avail Capacity Mounted on
/dev/ufs/OPNsense0 936M 734M 127M 85% /
devfs 1.0K 1.0K 0B 100% /dev
tmpfs 13M 372K 13M 3% /tmp
tmpfs 39M 26M 13M 68% /var
devfs 1.0K 1.0K 0B 100% /var/dhcpd/dev
7
15.7 Legacy Series / Re: [SOLVED] Can't upgrade freshly installed nano 15.7 to 15.7.7 on ALIX
« on: August 28, 2015, 04:30:33 pm »
I have always problems while upgrading the kernel (not enough space). I need to reboot and then try the upgrade again.
Will re-flashing fix that?
Will re-flashing fix that?
8
15.7 Legacy Series / Re: [SOLVED] Can't upgrade freshly installed nano 15.7 to 15.7.7 on ALIX
« on: August 28, 2015, 02:06:35 pm »
I already have an Alix running OPNsense. Do I have to re-flash with this new image to get enhancements provided by it?
Pages: [1]