Messages

1

Hardware and Performance / Re: Bandwidth cut in half when traversing system but direct bandwidth test is fine

« on: April 13, 2024, 11:08:27 am »

For those who seek answers...

We got it up to around 10G by fiddling around with some tunables: https://binaryimpulse.com/2022/11/opnsense-performance-tuning-for-multi-gigabit-internet/

Also, Some wired network switch links where replaced wich where responsible for die bandwidth halfling. Everything related to speed > 1G seems to be related to the tunables.

Thanks to all for tanking their time to read/help with this.

Kind regards

2

Hardware and Performance / Re: Bandwidth cut in half when traversing system but direct bandwidth test is fine

« on: April 05, 2024, 09:19:42 am »

Hi pholt,

sadly this did not help. I spent my night adding different old 10G network cards but i had no luck. Some weren't recognized at all, others didn't find a carrier. My test setup was a bit clunky, as i had to pull the unit out of the rack, which limited my DAC cable options.

At the end of the night, i ordered some Mellanox CX312A ConnectX-3. I had no problems with them on other FreeBSD systems in the past.

It is sad, as this system (Supermicro X10SDV-TP8F) was specifically bought because it hat dual SFP+ 10G. Now i have four systems of this type, all where the 10G ports are even worse then the 1G ports. Our supplier Thomas Krenn stated that this hardware is opensense compatible. Though i have not contacted their support, as i assume this does not qualify as a hardware issue.

Thanks for your help anyway.
Regards from here to there :-)

3

Hardware and Performance / Re: Bandwidth cut in half when traversing system but direct bandwidth test is fine

« on: April 04, 2024, 10:38:08 am »

Hi pholt,

thank you very much for taking your time to write a response. I will try this as soon as possible. Unfortunately i will have to wait until tonight to be able to test it. Just wanted to get a quick response out, as i am very grateful for your tip.

I will report back tonight.

 

4

Hardware and Performance / Bandwidth cut in half when traversing system but direct bandwidth test is fine

« on: April 01, 2024, 12:27:00 am »

Preamble
Hi there :-),
i have a problem with my opnsense setup that is strange to me, maybe someone has in idea on where to poke further.

The Situation/Problem

Given is a opnsense box on decent hardware (see hardware) that is supposed to route traffic from interface1 to interface2 or vice versa at nearly link speed (1G).

Launching iperf from the opnsense machine testing the connection to each system (ubuntu test machine and windows test machine) it reaches "at least high" speed.

From	To	Iperf result
opnsense	ubuntu	~833 Mbits/sec
opnsense	windows	~653 Mbits/sec
windows	ubuntu	~302 Mbits/sec

Observation
It seems that when traffic is routed through opnsense, my bandwidth is cut in half.

Code: [Select]

ix0,ix2                                                                                                               
media: Ethernet autoselect (10Gbase-Twinax <full-duplex,rxpause,txpause>)                                             
                                                                                                                       
                                                               ┌──────────────────────────────────────────────────────┐
                                                               │                       opnsense                       │
                                                               │                                                      │
┌──────────────────────┐                                       │                                                      │
│An Ubuntu test machine│                                       ├────────────┐                                         │
│192.168.77.47         │                                       │            ├────────────────┐     ┌─────────────┐    │
│                      │    Tagged    ┌──────────┐   Tagged    ├───┐        │ lagg0_vlan335  │◄───►│interface1   │    │
│CPU use < 25%         │◄────────────►│          │◄───────────►│ix0│        ├────────────────┘     │192.168.77.51│    │
└──────────────────────┘      1G      │ Multiple │    10G      ├───┘        │                      └─────────────┘    │
                                      │ Mikrotik │             │      lagg0 │                                         │
┌──────────────────────┐    Tagged    │ Switches │   Tagged    ├───┐        │                      ┌─────────────┐    │
│A Windows test machine│◄────────────►│          │◄───────────►│ix1│        ├────────────────┐     │interface2   │    │
│10.10.10.76           │      1G      └──────────┘    10G      ├───┘        │ lagg0_vlan1111 │◄───►│10.10.10.1   │    │
│                      │               Less then               │            ├────────────────┘     └─────────────┘    │
│CPU use < 25%         │               5% CPU use              ├────────────┘                                         │
└──────────────────────┘                                       │                                                      │
                                                               │          All CPUs are idle during transmission       │
                                                               └──────────────────────────────────────────────────────┘



Opnsense System

CPU type

Intel(R) Xeon(R) CPU D-1518 @ 2.20GHz (4 cores, 8 threads)

Memory usage

11 % ( 918/8044 MB ) { ARC size 229 MB }

Version

OPNsense 24.1.4-amd64

Network Card (onboard)

Intel(R) X552 (SFP+)

Mainboard

Supermicro X10SDV-TP8F

MTU related

Opnsense uses the following MTUs:

Interface

MTU

ix0

1470

ix1

1470

lagg0

1470

lagg0_vlan335

1300

What has been done so far

• Messed with the MTU (should not be a problem has the opnsense can communicate fine with ubnutu?)
• Checked and unchecked "Disable reply-to"
• Used "pfctl -d" temporarily to disable the firewall
• Unchecked all three of "Hardware CRC", "Hardware TSO" and "Hardware LRO"

I did not mess with the checkbox "VLAN Hardware Filtering" yet.

Special notes

• The system is in a HA mode with an identical other node
• The system has a lot (20+) Interfaces on vlans all on lagg0
• An IPSEC VDI Tunnel is again slower, even when using local ehternet only connection (just a side node, its what got the investigation started...)
• Checked CPU load on all related switches, all are sube 10% and bandwidth seems no issue aswell
• The system has only a few fw rules
• IPERF Options used (-w 64KB), tests added to the post are with "-t 2" but to shorten the output. longer tests show similar results

Some results

From opnsense to windows test machine

Code: [Select]

Connecting to host 10.10.10.76, port 6666
[  5] local 10.10.10.2 port 6661 connected to 10.10.10.76 port 6666
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.03   sec   105 MBytes   853 Mbits/sec    0    209 KBytes
[  5]   1.03-2.00   sec  98.6 MBytes   856 Mbits/sec    0    209 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-2.00   sec   204 MBytes   855 Mbits/sec    0             sender
[  5]   0.00-2.00   sec   204 MBytes   855 Mbits/sec                  receiver


From opnsense to ubuntu test machine

Code: [Select]

Connecting to host 192.168.77.47, port 6666
[  5] local 192.168.77.52 port 7437 connected to 192.168.77.47 port 6666
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec   109 MBytes   914 Mbits/sec    0   3.00 MBytes
[  5]   1.00-2.00   sec   108 MBytes   903 Mbits/sec    0   3.00 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-2.00   sec   217 MBytes   909 Mbits/sec    0             sender
[  5]   0.00-2.00   sec   217 MBytes   909 Mbits/sec                  receiver

From windows test machine to ubuntu test machine

Code: [Select]

Connecting to host 192.168.77.47, port 6666
[  4] local 10.10.10.76 port 57609 connected to 192.168.77.47 port 6666
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec  47.6 MBytes   399 Mbits/sec
[  4]   1.00-2.00   sec  49.0 MBytes   411 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-2.00   sec  96.6 MBytes   405 Mbits/sec                  sender
[  4]   0.00-2.00   sec  96.6 MBytes   405 Mbits/sec                  receiver

My questions

• Why can the system talk to the test machines so fast but traffic that traverses the opnsense is cut in half?
• Can i rule out MTU settings as the opnsense system can communicate fine when doing so directly? (it should use the same ports with the same vlans and so on... so it must be fine - right?)
• Is there any reason to doubt the network card or the driver when again, it can work fine communicating directly? I suppose not(?)

Update 2024-04-05

• Fiddling with the flow control sysctl setting did not help with the problem.
• Changing to different DAC cables CISCO, HP, Huawei (recommenden by our supplier for this card/board)

Code: [Select]

dev.ix.0.fc = 0
dev.ix.1.fc = 0
I would be greatfull for any advice. After days been spent on this problem i am losing my mind.

Kind regards and thanks in advance
SimonGuy