Messages

i had to change the speed of the nic in the opnsense to 10/100 but idk if thats going to help you

NIC was set to autoselect speed, changed to 1000t saved.
re ran speed test 500 500

all is good

Interfaces
WAN
Speed and duplex
1000baseT

all set

Looking for some direction purchased this off Amazon AWOW Mini PC Dual 2.5gb NIC 256GB SSD 8GB DDR4, Intel N5105 Mini Computer. Installed opsense ran through the wizard. No extra rules nothing. Pay for 500 up and down fiber frontier. Speed test on the firewall get 6 down. After messing with tunables. Get 20 down and 500 up. Can't figure out why

Any direction would be appreciated

Already disabled hardware checksum offload Created a vlan and added a parent to the wan port in interfaces

Looking for some direction purchased this off Amazon AWOW Mini PC Dual 2.5gb NIC 256GB SSD 8GB DDR4, Intel N5105 Mini Computer. Installed opsense ran through the wizard. No extra rules nothing. Pay for 500 up and down fiber frontier. Speed test on the firewall get 6 down. After messing with tunables. Get 20 down and 500 up. Can't figure out why

Any direction would be appreciated

Already disabled hardware checksum offload Created a vlan and added a parent to the wan port in interfaces

Connected on my wifi with my phone through Nord VPN get normal speed for WiFi

Thanks !


installed the realtek drivers through the plugins same thing.




igc0@pci0:1:0:0:        class=0x020000 rev=0x01 hdr=0x00 vendor=0x8086 device=0x15f3 subvendor=0x8086 subdevice=0x0000
    vendor     = 'Intel Corporation'
    device     = 'Ethernet Controller I225-V'
    class      = network
    subclass   = ethernet
    cap 01[40] = powerspec 3  supports D0 D3  current D0
    cap 05[50] = MSI supports 1 message, 64 bit, vector masks
    cap 11[70] = MSI-X supports 5 messages, enabled
                 Table in map 0x1c[0x0], PBA in map 0x1c[0x2000]
    cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS
                 max read 512
                 link x1(x1) speed 5.0(5.0) ASPM disabled(L1)
    ecap 0001[100] = AER 2 0 fatal 0 non-fatal 0 corrected
    ecap 0003[140] = Serial 1 00e04cffff6f1109
    ecap 0018[1c0] = LTR 1
    ecap 001f[1f0] = Precision Time Measurement 1
    ecap 001e[1e0] = L1 PM Substates 1
igc1@pci0:2:0:0:        class=0x020000 rev=0x01 hdr=0x00 vendor=0x8086 device=0x15f3 subvendor=0x8086 subdevice=0x0000
    vendor     = 'Intel Corporation'
    device     = 'Ethernet Controller I225-V'
    class      = network
    subclass   = ethernet
    cap 01[40] = powerspec 3  supports D0 D3  current D0
    cap 05[50] = MSI supports 1 message, 64 bit, vector masks
    cap 11[70] = MSI-X supports 5 messages, enabled
                 Table in map 0x1c[0x0], PBA in map 0x1c[0x2000]
    cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS
                 max read 512
                 link x1(x1) speed 5.0(5.0) ASPM disabled(L1)
    ecap 0001[100] = AER 2 0 fatal 0 non-fatal 0 corrected
    ecap 0003[140] = Serial 1 00e04cffff6f110a
    ecap 0018[1c0] = LTR 1
    ecap 001f[1f0] = Precision Time Measurement 1
    ecap 001e[1e0] = L1 PM Substates 1