Messages

You know what. I check the hardware and it was ok. I installed pfsense without any issue it just work the first time. I will check it out and see if it will work and maybe will give opnsense another chance but for now I am good.

Hello,

I had my old computer which was working fine and I have decided to turn it into router for my home.
I have bought INTEL PRO/1000 PT EXPI9402PTG2P20 DUAL PCIe LP and tried to install the OPNSense.

Upon booting it was crushing and didnt know why. I have removed the NIC and was able to install it with only port on my motherboard .

I have inserted the NIC back and it booted correctly I the nic and the interfaces on it and was able to assign lan interface to the Intel NIC.

However when I tried to setup the interfaces after it configures WAN it then goes int o kernel panic :

Code Select Expand


Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address   = 0x0
fault code              = supervisor write data, page not present
instruction pointer     = 0x20:0xffffffff80ece863
stack pointer           = 0x28:0xfffffe0060754cd8
frame pointer           = 0x28:0xfffffe0060754da0
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags        = interrupt enabled, resume, IOPL = 0
current process         = 12 (swi4: clock (0))
trap number             = 12
panic: page fault
cpuid = 0
time = 1688344784
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xfffffe0060754a90
vpanic() at vpanic+0x17f/frame 0xfffffe0060754ae0
panic() at panic+0x43/frame 0xfffffe0060754b40
trap_fatal() at trap_fatal+0x385/frame 0xfffffe0060754ba0
trap_pfault() at trap_pfault+0x4f/frame 0xfffffe0060754c00
calltrap() at calltrap+0x8/frame 0xfffffe0060754c00
--- trap 0xc, rip = 0xffffffff80ece863, rsp = 0xfffffe0060754cd8, rbp = 0xfffffe0060754da0 ---
nd6_na_input() at nd6_na_input+0x723/frame 0xfffffe0060754da0
softclock_call_cc() at softclock_call_cc+0x13d/frame 0xfffffe0060754e40
softclock() at softclock+0x79/frame 0xfffffe0060754e60
ithread_loop() at ithread_loop+0x25a/frame 0xfffffe0060754ef0
fork_exit() at fork_exit+0x7e/frame 0xfffffe0060754f30
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe0060754f30
--- trap 0x80d08f20, rip = 0xffffffff80c30e5f, rsp = 0, rbp = 0x180a ---
mi_startup() at mi_startup+0xdf/frame 0x180a
KDB: enter: panic


My full hardware setup is as follows:
- Motherboard : Asus P8B75-M LX
- RAM : HyperX 2x4GB 1600MHz DDR3 Non-ECC CL9 Intel XMP X2 Grey Series (KHX1600C9D3X2K2/8GX)
- CPU : Celeron G1610, Dual Core, 2.60GHz, 2MB, LGA1155, 22nm, 55W, VGA, BOX (BX80637G1610)
- NIK : NTEL PRO/1000 PT EXPI9402PTG2P20 DUAL PCIe LP
- SSD: SDNow V300 120 GB 7mm (SV300S37A/120G)

Please let me know what I can do to set it up? What I am doing wrong ?