Messages

1

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 28, 2023, 05:00:19 am »

I was able to get into the GUI once I changed the Lan IP address it says it’s applying changes and lost connection to the computer, the power is still on so I try the new IP address and it will not load, try rebooting it still no GUI at the new address? I found a windows PC has a range for IPs is that a possibility?

2

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 11:30:23 pm »

You were right the fresh install did the trick, I’m on the GUI, now I have to read up on this.

3

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 11:12:15 pm »

You’re on to something fresh install got me online with the LAN A0 aka default. Now do I setup everything then connect the WAN?

4

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 11:01:31 pm »

Windows diagnostic says Ethernet doesn’t have a valid IP address

5

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 10:56:52 pm »

The interfaces have been reset, no it’s Lan A0, A1, A2, and WAN A3. No connection to it on LAN A0. Connect it to home router on WAN A3, still no LAN connection.. rebooting now no LAN connection. LAN address is 192.168.1.1,

6

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 10:22:23 pm »

Yes it sets the LAN first, I set A1, A2, A3 not A0, then it asks me to set the WAN that’s is A0. So the LAN is supposed to be first? Then that would make the WAN A3? If I set it up
That way.

7

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 09:15:47 pm »

The WAN is set to plug label A0, that was and is the input from the mean router. LAN’s are A1, A2, A3, unfortunately I just get no response from ip 192.168.1.1 on the LAN A1 or the other two. My PC has both DHCP and IPV4 on. Could you recommend a good book on networking?

My network:

Home router> switch > opnsense > windows PC

8

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 08:31:45 pm »

With the first install of opnsense 23.1 I wasn’t able to load the GUI on the LAN 192.168.1.1 or 192.168.1.0, with my windows pc. Then I rebooted it same issue again. Next I set the Lan to 10.10.10.1 and was unable to open the GUI at that address as well. Next I rebooted the upstream router no improvement. Next I rebooted both the upstream router and the opnsense PC, no GUI, just to be sure I reinstalled opnsense. That didn’t fix it, setting my CR1000 the upstream router to bridge mode just crashed it, no I’m with a new install with the Wan set to A0 and the Lan A1-3, automatic ip settings. There is an internet connection to the Opnsense PC I can ping it’s console.

9

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 27, 2023, 04:39:09 pm »

Thanks for the reply,
But unfortunately I did that and it didn’t work

10

23.1 Legacy Series / Re: Default setup, but no internet access on LAN

« on: March 27, 2023, 04:35:42 pm »

Hi,
Where you able to use it behind the Verizon router after?

11

23.1 Legacy Series / Re: OPNSense 23.1.4 Web GUI Instablility Issues

« on: March 27, 2023, 04:34:00 pm »

Hi,
I’m have the same No GUI issue with version 23.1 with my N4015 VENOEN MINI PC. Do you have Verizon?

12

22.1 Legacy Series / Re: No GUI and no Lan access

« on: March 26, 2023, 05:45:53 pm »

After more testing it’s a double Nat issue, the router required by ISP has the same default Lan address. Can another router be added in between them be used to solve the issue? And yes I tried changing the Lan IP on the opnsense firewall. Still no Lan connection

13

22.1 Legacy Series / No GUI and no Lan access

« on: March 25, 2023, 06:19:56 pm »

The OPNsense is installed on a mini PC with 4 Ethernet ports. I can boot it and use the video out on it to see that I have internet to it and an Ip address. No Lan connection from it but it shows the IP I set?