Messages

HI.

Opnsense installed from official image - 22.7. Setup, config, startup - no problems, no errors.

first thing update after config wizard, reboot then getting long time startup and errors:

ahci0: <AHCI SATA controller> port 0x3090-0x3097,0x3080-0x3083,0x3060-0x307f mem 0x80800000-0x80801fff,0x80803000-0x808030ff,0x80802000-0x808027ff at device 23.0 on pci0
ahci0: AHCI v1.31 with 1 6Gbps ports, Port Multiplier not supported
ahcich1: <AHCI channel> at channel 1 on ahci0
ada0 at ahcich1 bus 0 scbus0 target 0 lun 0
ahcich1: Timeout on slot 26 port 0
ahcich1: is 00000000 cs 00000000 ss 04000000 rs 04000000 tfd 50 serr 00000000 cmd 0000c917
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 3 more tries remain
ahcich1: Timeout on slot 14 port 0
ahcich1: is 00000000 cs 00000000 ss 00004000 rs 00004000 tfd 40 serr 00000000 cmd 0000ce17
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 2 more tries remain
ahcich1: Timeout on slot 19 port 0
ahcich1: is 00000000 cs 00000000 ss 00080000 rs 00080000 tfd 40 serr 00000000 cmd 0000d317
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 1 more tries remain
ahcich1: Timeout on slot 24 port 0
ahcich1: is 00000000 cs 00000000 ss 01000000 rs 01000000 tfd 40 serr 00000000 cmd 0000d817
(ada0:ahcich1:0:0:0): SEND_FPDMA_QUEUED DATA SET MANAGEMENT. ACB: 64 01 00 00 00 40 00 00 00 00 00 00
(ada0:ahcich1:0:0:0): CAM status: Command timeout
(ada0:ahcich1:0:0:0): Retrying command, 0 more tries remain
ahcich1: Timeout on slot 29 port 0

any ideas? thanks

UPDATE:

Flashed a new bios from here (https://www.changwang.com/down/59.html) on the off-chance it works and solves the issue.

Solved the issue. The frequency now scales up and down based on usage.

Here's a dump of my tunables as well:

Code Select Expand

dev.hwpstate_intel.0.epp Intel Speed Shift Efficiency runtime 100
dev.hwpstate_intel.1.epp Intel Speedshift Efficiency runtime 100
dev.hwpstate_intel.2.epp Intel Speedshift Efficiency runtime 100
dev.hwpstate_intel.3.epp Intel Speedshift Efficiency runtime 100
dev.igc.0.fc Flow Control on Interface runtime 0
dev.igc.1.fc Flow Control on Interface runtime 0
dev.igc.2.fc Flow Control on Interface runtime 0
dev.igc.3.fc Flow Control on Interface runtime 0
hint.hwpstate_intel.0.disabled disable speed shift unsupported 0
hw.acpi.cpu.cx_lowest C-States runtime C1
machdep.hwpstate_pkg_ctrl Intel Pstate boot-time 0

Hi. I also flashed a bios on my N6006 unit but it seems I broke it, I no longer have video. Unfortunately, support in basically non-existent and the update from Chanwang site (link above) is not a full BIOS. Do you tink it's possible for your to send me a full dump of the BIOS from your unit? cand be done via UEFI boot process.