1
23.7 Legacy Series / Re: Block traffic between interface LAN
« on: February 28, 2024, 10:30:38 am »
Ok thank you i create alias network with all lan networks, and then create a rule like this and it works!!!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
23.7 Legacy Series / Re: Block traffic between interface LAN
« on: February 27, 2024, 04:23:00 pm »
Hi Patrick
I have attached the current firewall rules that I have on the interfaces vmbr0 up to vmbr6 excluding vmbr1 which is the wan.
With the following two rules I can surf the internet so it's fine. But I would like to create a rule where it can only go to the internet but can't go to the other networks which are on the other interfaces.
What rule should I create? Can you give some examples? Thanks.
I have attached the current firewall rules that I have on the interfaces vmbr0 up to vmbr6 excluding vmbr1 which is the wan.
With the following two rules I can surf the internet so it's fine. But I would like to create a rule where it can only go to the internet but can't go to the other networks which are on the other interfaces.
What rule should I create? Can you give some examples? Thanks.
3
23.7 Legacy Series / Block traffic between interface LAN
« on: February 27, 2024, 04:01:25 pm »
HI all
I attach my network diagram so you can understand what i want to achieve
Basically i want only the interface lan vmbr0,vmbr2,vmbr3,vmbr4,vmbr5,vmbr6 have access only on wan interface to go out and reach internet, i don't want vmbro can talk to vmbr2 and viceversa.
Thanks
I attach my network diagram so you can understand what i want to achieve
Basically i want only the interface lan vmbr0,vmbr2,vmbr3,vmbr4,vmbr5,vmbr6 have access only on wan interface to go out and reach internet, i don't want vmbro can talk to vmbr2 and viceversa.
Thanks
4
23.1 Legacy Series / Re: Help to configure Collectd
« on: April 04, 2023, 02:37:45 pm »
i don't have thies field like your screenshoot i think...
5
23.1 Legacy Series / Re: Help to configure Collectd
« on: April 04, 2023, 10:26:40 am »
Ok but in my case what type of dashboard i need for my scenario?
InfluxDB o Graphite?
InfluxDB o Graphite?
6
23.1 Legacy Series / Re: Help to configure Collectd
« on: April 04, 2023, 09:28:06 am »
HI @pmhausen
Any good news?
I can't understand how to configure dashboard to receive data...
Any good news?
I can't understand how to configure dashboard to receive data...
7
23.1 Legacy Series / Re: Problem with Airprint
« on: April 04, 2023, 08:57:09 am »
Hi i resolved enable this option in Unifi Controller:
Global Network Settings > Multicast DNS
Global Network Settings > Multicast DNS
8
23.1 Legacy Series / Problem with Airprint
« on: April 03, 2023, 11:54:58 am »
Hi
After install OPNSense my customer can't print to airprint printers, what should i do?
Thanks
After install OPNSense my customer can't print to airprint printers, what should i do?
Thanks
9
23.1 Legacy Series / Re: Help to configure Collectd
« on: April 03, 2023, 10:10:45 am »
Hi
I don't know how to configure dashborad to receive data(see screenshoots)
I don't know how to configure dashborad to receive data(see screenshoots)
10
23.1 Legacy Series / Re: Help to configure Collectd
« on: March 31, 2023, 12:28:52 pm »
Hi
I import a dashboard for OPNSense by searching in "https://grafana.com/grafana/dashboards/"
see the screenshoot for details
Anyway if you have a nice dashboard for opnsense can you send me the code for import
Thanks
I import a dashboard for OPNSense by searching in "https://grafana.com/grafana/dashboards/"
see the screenshoot for details
Anyway if you have a nice dashboard for opnsense can you send me the code for import
Thanks
11
23.1 Legacy Series / Re: Help to configure Collectd
« on: March 31, 2023, 11:33:03 am »
Hi
The command you tell me to use working correcty (see the screenshoot)
The command you tell me to use working correcty (see the screenshoot)
12
23.1 Legacy Series / Re: Help to configure Collectd
« on: March 31, 2023, 09:52:30 am »
Off course is not related to OPNSense, so don't worry
This is the actual file /etc/influxdb/influxdb.conf:
[meta]
dir = "/var/lib/influxdb/meta"
[data]
dir = "/var/lib/influxdb/data"
engine = "tsm1"
wal-dir = "/var/lib/influxdb/wal"
[[graphite]]
enabled = true
database = "opnsense"
retention-policy = ""
bind-address = ":2003"
protocol = "tcp"
consistency-level = "one"
separator = "."
templates = [
"servers.* .hostname.resource.instance.measurement*",
]
I attach screenshoot about OPNSense CollectD Configuration and Grafana Dashboard, as you can see i don't receive data from collectd.
This is the actual file /etc/influxdb/influxdb.conf:
[meta]
dir = "/var/lib/influxdb/meta"
[data]
dir = "/var/lib/influxdb/data"
engine = "tsm1"
wal-dir = "/var/lib/influxdb/wal"
[[graphite]]
enabled = true
database = "opnsense"
retention-policy = ""
bind-address = ":2003"
protocol = "tcp"
consistency-level = "one"
separator = "."
templates = [
"servers.* .hostname.resource.instance.measurement*",
]
I attach screenshoot about OPNSense CollectD Configuration and Grafana Dashboard, as you can see i don't receive data from collectd.
13
23.1 Legacy Series / Re: Help to configure Collectd
« on: March 30, 2023, 11:20:21 am »
UPDATE:
I see one problem after edit the infludb container for mapping port 2003/tcp now the configuration file in /etc/influxdb/influxdb.conf lost the changes for graphite connector.
How to make persistant if i need to edit the container?
I see one problem after edit the infludb container for mapping port 2003/tcp now the configuration file in /etc/influxdb/influxdb.conf lost the changes for graphite connector.
How to make persistant if i need to edit the container?
14
23.1 Legacy Series / Re: Help to configure Collectd
« on: March 30, 2023, 09:37:42 am »
Hi
I've mapping both ports on the host running docker port tcp/8086 and tcp/2003 on influxdb container, on my opnsense firewall in collectd i have configure like the screenshoot you send me, i download a dashboard for opnsense in grafana dashboard website and import the dashboard but i don't receive data from OPNSense Firewall.
I've mapping both ports on the host running docker port tcp/8086 and tcp/2003 on influxdb container, on my opnsense firewall in collectd i have configure like the screenshoot you send me, i download a dashboard for opnsense in grafana dashboard website and import the dashboard but i don't receive data from OPNSense Firewall.
15
23.1 Legacy Series / Re: Help to configure Collectd
« on: March 30, 2023, 08:50:21 am »
Hi i have add the database (see screenshoots), but this server has to be reach external, in portainer as you can see the port exposed to the host is only the 8086, i need to redeploy the container influxdb choose port 2003/tcp instead 8086/tcp?