"
Hi Pocket_Sevens,
they had been displayed on the console after entering the command.
they had been displayed on the console after entering the command.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
21.1 Legacy Series / [SOLVED] How to disable TRIM for a SSD permanently ?
March 05, 2021, 04:31:53 PM
I booted into single user mode and typed in
I exit the single user mode and started the firmware update via the WebGUI.
After another reboot i could access the firewall without any error messages.
Thank you very much for your quick and competent support.
Code Select
# tunefs -t disable /
tunefs: issue TRIM to the disk remains unchanged as disabled
tunefs: file system reloaded
I exit the single user mode and started the firmware update via the WebGUI.
After another reboot i could access the firewall without any error messages.
Thank you very much for your quick and competent support.
#3
21.1 Legacy Series / How to disable TRIM for a SSD permanently ?
March 05, 2021, 03:41:25 PM
Spec: Mini PC RM02 from HUNSN, Intel Core I5 8365U, 8GB DDR4, 256GB SSD, 6 Intel I211-AT Gigabit Nics
Using macOS i downloaded the latest VGA installer (OPNsense-21.1-OpenSSL-vga-amd64.img.bz2), extracted it, and then used balenaEtcher to write the image to an USB flash drive.
I booted the HUNSN PC via the USB flash drive to the OPNsense live environment and installed OPNsense with no issue.
After rebooting it came up fine and i began configuring OPNsense via the GUI. Everything was going great.
Then after another reboot i got lots of
messages.
And from than on i got these message after every boot.
After a research in this forum i found that disabling TRIM for the SSD could be the solution.
I followed the tip to modify /usr/local/etc/rc regarding disabling TRIM via tunefs -t disable /dev/gpt/rootfs.
(where /dev/gpt/rootfs is the filesystem listed in /etc/fstab) then reboot.
That solved the problem for me.
But after updating OPNsense to the current version i had the old /usr/local/etc/rc and TRIM was enabled again.
The camcontrol command shows the following information
It seems the that SSD does not support TRIM but i dont know why TRIM is set to "yes".
Is it possible to disable TRIM for the SSD permanently ?
Any help is appriciated.
Best regards
Jürgen
Using macOS i downloaded the latest VGA installer (OPNsense-21.1-OpenSSL-vga-amd64.img.bz2), extracted it, and then used balenaEtcher to write the image to an USB flash drive.
I booted the HUNSN PC via the USB flash drive to the OPNsense live environment and installed OPNsense with no issue.
After rebooting it came up fine and i began configuring OPNsense via the GUI. Everything was going great.
Then after another reboot i got lots of
Code Select
ahcich0: Timeout on slot ....
ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED ...
ada0:ahcich0:0:0:0): CAM status: Command timeout ...
ada0:ahcich0:0:0:0): Retrying command ...
messages.
And from than on i got these message after every boot.
After a research in this forum i found that disabling TRIM for the SSD could be the solution.
I followed the tip to modify /usr/local/etc/rc regarding disabling TRIM via tunefs -t disable /dev/gpt/rootfs.
(where /dev/gpt/rootfs is the filesystem listed in /etc/fstab) then reboot.
That solved the problem for me.
But after updating OPNsense to the current version i had the old /usr/local/etc/rc and TRIM was enabled again.
The camcontrol command shows the following information
Code Select
root@OPNsense:~ # camcontrol devlist
<SATA SSD SBFM01.3> at scbus0 target 0 lun 0 (ada0,pass0)
Code Select
root@OPNsense:~ # camcontrol identify ada0 | grep TRIM
Data Set Management (DSM/TRIM) yes
It seems the that SSD does not support TRIM but i dont know why TRIM is set to "yes".
Is it possible to disable TRIM for the SSD permanently ?
Any help is appriciated.
Best regards
Jürgen
Pages1
